-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueSilicon to Systems: From Soup to Nuts
This month, we asked our expert contributors to weigh in on silicon to systems—what it means to PCB designers and design engineers, EDA companies, and the rest of the PCB supply chain... from soup to nuts.
Cost Drivers
In this month’s issue of Design007 Magazine, our expert contributors explain the impact of cost drivers on PCB designs and the need to consider a design budget. They discuss the myriad design cycle cost adders—hidden and not so hidden—and ways to add value.
Mechatronics
Our expert contributors discuss the advent of mechatronics in PCB design, the challenges and opportunities this creates for circuit board designers, and the benefits—to the employee and the company—of becoming a mechatronics engineer.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Going Green at SEL
August 23, 2023 | Barry Matties, I-Connect007Estimated reading time: 2 minutes
A Q&A with John Hendrickson, engineering director at Schweitzer Engineering Laboratories.
SEL is going green at its new 162,000-square-foot, environmentally friendly PCB manufacturing facility in Moscow, Idaho. As John Hendrickson explains, being a zero liquid discharge (ZLD) facility—a trend you are likely to hear more of in our industry—is not just a smart business decision, it’s driven by SEL’s core values.
Barry Matties: As far as waste treatment goes, this is a zero liquid discharge (ZDL) facility, correct?
John Hendrickson: Yes, it's zero discharge. We have zero drains in our manufacturing floor and zero drains in our water recycling room. The only drains we have are in our bathrooms and sinks; even the sinks in our lab are all pumped to our water recycling. There's no opportunity for somebody to dump something down the wrong sink.
We designed the factory with a chemical-resistant membrane underneath the facility. We designed the floor so that it slopes a little bit to the center. If we ever had a major spill on this floor, it would all go to the center of the floor and it would all be contained within the building. In the water recycling room, we dropped the floor six inches.
The way this system works is that we have two primary inputs in the system for our rinse waters, which we manage separately from our concentrate side. On the concentrate side, we take the material and drop the metals out and then change the pH. Then we take that through our filter press. So that's where our metals are, and that goes out for recycling.
Everything else will move over to what we call a pH batch tank. We adjust that to a pH of 7 and then we run that through our evaporators. After the concentrate goes to the evaporators, then we take it to a dryer, and we're still putting it under pressure and heat evaporating and then it goes back to the rinse inside. On the rinse side, we'll take it through ozone, then we'll destruct the ozone with UV. We run that through a GAC (granular activated carbon) column, through ion exchange columns, and then eventually run it through reverse osmosis. That’s how we generate our DI water.
Matties: Is this kind of thinking why the city got behind this factory?
Hendrickson: Yes. The fume scrubber and everything else definitely helped us with our EPA requirements. Visiting officials have all been very impressed by how clean the factory is and how we've managed some of these things. In fact, some of the things that we’re doing with this equipment have never seen an application in the state before.
Matties: Thank you, John.
This conversation appeared in the August 2023 issue of PCB007 Magazine.
Suggested Items
DuPont Expands Photoresist Manufacturing Capacity at Sasakami Site in Japan
10/04/2024 | PRNewswireDuPont announced the successful completion of a significant expansion for photoresist manufacturing capacity at the DuPont Sasakami Site in Agano-shi, Niigata, Japan.
Global PC Monitor Market Delivers Third Consecutive Quarter of Growth in Q2 2024
09/18/2024 | IDCThe global PC monitor market ended the second quarter of 2024 with 5.9% growth in unit shipments compared to the same quarter a year ago.
Cirtronics Welcomes Patrick Moody as New CEO to Lead Next Era of Growth
09/12/2024 | CirtronicsCirtronics, a leading advanced contract manufacturing firm, is excited to announce the appointment of Patrick Moody as the new President, Chief Executive Officer (CEO), and Board of Directors member. Founder and former CEO Gerardine Ferlins will continue to contribute to Cirtronics’ legacy by remaining on the company’s Board of Directors.
MEK Launches New PowerSpector JSAz 550: Larger 3D Desktop AOI System with New Chassis
09/11/2024 | MEKMek (Marantz Electronics), a leader in Automated Optical Inspection (AOI) and Solder Paste Inspection (SPI) technology, proudly announces the launch of its latest product, the PowerSpector JSAz 550. This new selective 3D desktop AOI system is a larger L-size model, capable of accommodating Printed Circuit Boards (PCBs) up to 550x550mm (21.7”x21.7”).
Würth Elektronik eiSos Appoints New Executive VP
09/10/2024 | Wurth Elektronik eiSosThomas Garz has been appointed Executive Vice President for the Würth Elektronik eiSos Group with effect from 1 August 2024. The 37-year-old has been with the Würth Group since 2006.