-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueSilicon to Systems: From Soup to Nuts
This month, we asked our expert contributors to weigh in on silicon to systems—what it means to PCB designers and design engineers, EDA companies, and the rest of the PCB supply chain... from soup to nuts.
Cost Drivers
In this month’s issue of Design007 Magazine, our expert contributors explain the impact of cost drivers on PCB designs and the need to consider a design budget. They discuss the myriad design cycle cost adders—hidden and not so hidden—and ways to add value.
Mechatronics
Our expert contributors discuss the advent of mechatronics in PCB design, the challenges and opportunities this creates for circuit board designers, and the benefits—to the employee and the company—of becoming a mechatronics engineer.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
TECHNICAL PAPER: Novel Automatic Repair of Populated PCBs in a Cost-effective and Adaptive Way
February 21, 2024 | Essemtec, a NanoDimension DivisionEstimated reading time: 3 minutes
Introduction
Did you ever have to consider repairing an electronic product? Repairing populated boards is getting more and more popular due to several reasons, for example, placement of wrong components, refurbishment or function enhancement of existing products, counterfeit components, etc. The cost of the top five most counterfeited parts represents $169 billion worth of semiconductor revenue. Around 140,000 tons of electronic products are wasted every day globally with few repair options on the market, representing the fastest-growing category of waste in developed countries.
Changing an electrical component is a tedious job. Desoldering it from the board, removing the extra solder from the pads, applying fresh solder and flux to the component or pads, placing the new component, and finally soldering the component again are the typical processes involved. Regarding soldering, there are two ways to perform this process, the first is heating only the affected component locally, and the second is using low-temperature solder, which allows submitting the whole product to temperature. Two main disadvantages of the current repair process are the use of the valuable time of expert personnel and that only one component per product can be replaced at a time. Applying solder paste and placing the component is very problematic, especially on fine-pitch components—the risk of short circuits due to misplacements of packages or solder paste is high.
The proposed method in this work is focused on applying solder paste and placing the component. By using solder jetting instead of printing or dispensing, the time required to deposit solder paste can be significantly reduced. Special needles were designed to perform the jetting process without damaging the already populated components. Another advantage of using a fully programmable jetting system is that the required volume can be customized per pad; for example, pads for a TQFP package with 200 μm width pins and a large pad in the middle can easily be jetted, delivering the correct amount depending on the situation. Pick and place of the components is performed with the same instrument as well in a fully automatic way and the throughput is further improved. The possibility to replace several components on the same product is also given. There is no need for an expert operator once the equipment is programmed.
The repair process has been implemented with different alloys, including SnPb, SAC305, and SnBi. This work presents the results of products reworked using SnPb and SnBi. The results show that the XY positioning accuracy and dot repeatability exceed acceptable expectations for a 400 μm pitch. With this fully automatic jetting and pick-and-place method, the repair of a product can be made in a very accurate and agile way. This represents remarkable cost advantages for companies performing repairing activities.
Experimental Methodology
The experimental studies aim to test the positioning accuracy of the solder deposits as well as the dot repeatability. The throughput achieved with the proposed repair method was also measured. The positioning and dot accuracy was assessed against product needs, and the throughput was compared with the current customer experience. All the accuracy data was collected at Essemtec’s lab, and the throughput data was collected at the customer’s facilities.
Even though every soldered component type can be repaired with the proposed method, this work only analyzed two cases. The first one is a product with a TQFP (thin quad flat package) component requiring a type 6 paste with a Sn63Pb37 alloy. This TQFP has 128 terminals of 200 μm in width with a pitch of 400 μm and a contact area in the middle of 8.4 x 8.4 mm. The size of the TQFP is 14 x14 mm. The second case is a product with a BGA using a low temperature soldering type 6 paste with a Sn63Bi37 alloy. This BGA has a total of 1599 terminals with a diameter of 200 μm and a pitch of 400 μm, the size of the BGA is 18.5 x 27 mm.
A total of 20,000 dots were jetted to verify the stability of the jetting process. For every 1,000 dots jetted on production, 10 dots were jetted on a separate test plate where the dot’s diameter and X-Y accuracy was measured. A total of 200 data points were collected per experiment.
Positioning accuracy and precision together with the dot diameter were measured utilizing the ePlace software which is integrated into Essemtec machines. A normality test was performed on all data using the Anderson Darling method. A capability analysis was performed on every data set using the Minitab software version 19.
Continue reading this paper in the January 2024 issue of SMT007 Magazine.
Suggested Items
Altium, Mouser Team Up to Advance Electronics Education and Careers Worldwide
09/05/2024 | AltiumAltium LLC, a global leader in software and solutions for the electronics industry, and Mouser Electronics, a global authorized distributor of semiconductors and electronic components, are excited to announce a strategic partnership aimed at advancing electronics education and careers worldwide.
Quiet Power: An Evolution in PCB Design Costs
09/04/2024 | Istvan Novak -- Column: Quiet PowerIn this column, I want to cover my experiences, particularly where costs are concerned, with printed circuit boards from the 1960s to the present day. I grew up in an apartment building in downtown Budapest, where I began doing hobby projects building circuits from our kitchen table. Now, I’m lecturing about the most recent advances in signal integrity at Oxford University. We’ve come a long way. Over the decades, new technologies allowed users to have more layers, lower-loss dielectrics, fine-pitch surface connections, blind and buried vias, and HDI and HDI+ board constructions that allow us to design higher-performing systems. I expect this trend to continue.
CELUS Goes Global with Simplified Electronics Design Process
08/29/2024 | BUSINESS WIRECELUS, announced the worldwide availability of its revolutionary AI assisted hardware design platform that empowers engineers with the ability to find the right components for their projects through smart algorithms and the use of machine learning and AI.
Global Sourcing Spotlight: A World Full of Product Expertise
08/28/2024 | Bob Duke -- Column: Global Sourcing SpotlightWhen it comes to global sourcing, not all countries and products are created equal. Over the years, through travel and experience, I have discovered where to find the best products. Interestingly, certain countries have developed expertise in producing certain products. When it comes to industrial and electronic products, certain regions and countries are renowned for their expertise and manufacturing capabilities in specific areas. I am sure someone could write a book, and perhaps someone already has, about why certain countries excel in producing certain products.
Kopin Awarded First Order for High Resolution Microdisplay Assembly for Use in Sophisticated Electronics Manufacturing Systems
08/20/2024 | BUSINESS WIREKopin Corporation announced that it received the first production purchase order for its high resolution, 4 Megapixel 2K-R11 FLCoS Spatial Light Modulator (SLM) system for use within 3D AOI ("3-Dimensional Automated Optical Inspection") machines.