Beyond Design: AI-driven Inverse Stackup Optimization
Global PCB Connections: Following DFM Rules Leads to Better Boards
Elementary Mr. Watson: How to Reinvent Your Professional Journey
Scrutinizing Solder Printing
September 10, 2024 | Nolan Johnson, I-Connect007Estimated reading time: 2 minutes
As members of the technical staff at Indium, Adam Murling, technical manager, and Ron Lasky, senior technologist and professor at Dartmouth University, know their way around metallurgy and solder formulation. I corralled them for a conversation on solder application techniques from the solder’s perspective and their insights did not disappoint.
Nolan Johnson: Adam, what are some threshold moments when you go to solder jetting over solder printing?
Adam Murling: It’s a tandem approach, not all-or-nothing. Let’s say you have a four- or five-mils- (100 to 123 micron) thick stencil, but you also have really fine-pitch BGAs on the same device. There's an argument to be made for not cutting those apertures out because the area ratio will be too challenging.
But then you have a jet or dispenser down the line that can take care of those finer particles, and you want to make sure that the flux chemistry is compatible with the paste you're using in a jet as well as the solder paste on the screen printer; they need to be compatible.
But what happens when things are too large? You have most smaller devices—the 01005s, the 0201s and 0.3-millimeter pitch BGAs, etc.—but you also have connectors that require more solder volume than a 3-mil (75 micron) stencil can provide. You can always use a step stencil—it's been a practice for a long time—but at the same time it causes some process challenges.
If you had both pieces of equipment (stencil printing and jetting) you could then do additive manufacturing and essentially jet the paste on top of your 3-mil (75 micron) height, which was deposited through the stencil, to get more solder volume before placing the connector in place.
Johnson: If you factor in additive manufacturing thinking to solder paste application to get a certain height, does that become a designer concern as much as an assembly concern?
Murling: Nolan, everything's going super small. You're having these automotive manufacturers that are getting into the space and they're not able to find those larger parts that they're comfortable working with anymore. Everyone's focusing more on the smaller devices. They're more readily available with the same power output, but they still need those connectors. You will need a step stencil or you could do the additive approach.
To read this entire conversation, which appeared in the September 2024 issue of SMT007 Magazine, click here.
Share on:
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 5
12/23/2024 | I-Connect007 Editorial TeamChapter 5 introduces the advantages of using low-temperature soldering for through-hole components, including cost efficiency, reliability improvement, and reduced warpage. Also covered: the evaluation of different fluxes and the performance of HRL3 in wave soldering and selective soldering processes.
Overview of Soldering Systems With Vacuum
12/18/2024 | Dr. Paul Wild, Rehm Thermal Systems GmbHWhen soldering electronic assemblies, the focus of the vacuum application is on the removal of volatile substances from the solder joints and the associated reduction of pore formation. Particularly in the thermal management of power electronics components, pores can cause so-called hotspots with higher temperatures due to their poor heat conduction. These hotspots can lead to overheating of the components on the one hand and to thermally induced destruction of the solder structure on the other.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
12/13/2024 | Andy Shaughnessy, I-Connect007This week, Peter Tranitz discusses the upcoming Pan-European Electronics Design Conference, set for Jan. 29-30 in Vienna, Austria. Pete Starkey brings us a review of the most recent EIPC Technical Snapshot webinar, which featured a global PCB maker update by Dr. Hayao Nakahara. Don't miss our interview with Manfred Huschka, who explains how companies can begin their own China Plus One plan. Stan Farnsworth breaks down photonic soldering and discusses its use in soldering materials that are not typically compatible. I also enjoyed Dan Beaulieu’s discussion on the value of consistency, and why just showing up for work is half the battle, especially in an inconsistent, evolving industry like ours.
Advancing Photonic Soldering
12/11/2024 | Nolan Johnson, SMT007 MagazineStan Farnsworth, director of customer satisfaction at PulseForge, discusses the advancements in photonic soldering that highlight its energy efficiency and versatility. Over the past two years, the company has refined its applications for flexible substrates and energy reduction, finding that photonic soldering allows the processing of materials that typically aren’t thermally compatible and offers significant energy savings compared to traditional methods.
Indium Introduces New ROL0 and Halogen-free Flux-cored Wire
12/11/2024 | Indium CorporationIndium Corporation announced the global availability of CW-807RS, a new high-reliability, halide- and halogen-free flux-cored wire that improves wetting speeds and cycle times for electronics assembly and robot soldering applications.