Beyond Design: High-speed Rules of Thumb
Global PCB Connections: A Technical Overview of Long-flex Printed Circuit Boards
The Shaughnessy Report: A Handy Look at Rules of Thumb
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 4
October 3, 2024 |Estimated reading time: 1 minute
Chapter 4: Challenges in Maintaining the High Electrical Reliability of Low-temperature Solder Pastes
With the rapid advancement of technology and changes in end-user expectations, portable electronics such as mobile and computing devices are becoming increasingly thinner while requiring enhanced processing power. To meet these requirements, a new generation of electronic assembly materials is needed. Low-temperature solders with a melting temperature of 138°C are widely preferred by many semiconductor package manufacturers for assembling packages onto printed circuit boards. Most of these packages are very thin and require high performance.
As mentioned in previous chapters, lower peak reflow temperatures are being increasingly adopted in surface mount applications as package densities continue to increase in mobile and wearable devices. Lower peak reflow temperature helps to prevent warpage-induced defects in large and thin components. However, reducing the peak reflow temperature poses a potential issue to electrical reliability as lower peak reflow temperatures may promote electrical failure. Performance matrix: An SIR value greater than 1E+08 Ohm throughout the test duration (168 hours) is considered as pass.
The residue remaining after SMT reflow is almost always responsible for compromising the electrical reliability properties, such as surface insulation resistance and electrochemical migration under a given temperature with humidity. There is a need for a flux that passes all the given electrical reliability properties as specified by industry standards such as IPC and JIS.
In general, the design of a solder flux consists of many organic chemicals such as rosins, solvents, weak organic acids, amines, rheology modifiers, and other additives. These chemicals combine to form a homogeneous mixture called flux. The main function of the flux, when mixed with metallic powder, is to remove the oxide layer on the surface of each powder particle and prepare the adhering surface for soldering. The final critical properties of the solder paste, such as wetting, non-wet opening, and head-in-pillow, are extremely dependent on the type of flux and its constituents. Low-temperature reflow solder alloys create unique challenges for chemistry design. By considering the requirement and the critical factors involved in achieving higher electrical properties of low-temperature solders, much time and resources have been spent solving the challenges of engineering a new flux chemistry platform with advanced chemical molecules.
Share on:
Suggested Items
DELO Introduces UV-approach for Fan-out Wafer-level Packaging
10/25/2024 | DELODELO has developed a new approach for fan-out wafer-level packaging (FOWLP). Its feasibility study shows: With the use of UV-curable molding materials instead of heat curing ones, warpage and die shift can be reduced significantly. Additionally, this leads to improvements in curing time and minimizes the energy consumption.
Indium to Showcase Industry-Leading Solder Paste and Alloy Technology at Detroit Battery Show
10/01/2024 | Indium CorporationAs one of the leading materials providers to the electronics assembly industry, Indium Corporation® is proud to feature its industry-leading Durafuse® solder technology at the Battery Show North America, October 7-10, in Detroit, Michigan.
Book Excerpt: The Printed Circuit Designer’s Guide to... Thermal Management with Insulated Metal Substrates, Vol. 2, Chapter 4
09/25/2024 | I-Connect007 Editorial TeamDirect-bonded copper (DBC) with a ceramic base is a commonly used assembly technology. While advantages include excellent solder crack compensation due to similar CTE values between component and substrate, the construction is fragile and therefore places limits on size and exposure to vibration. Small assemblies in basic shapes such as a rectangle can be done, although larger, more complex shapes become difficult.
Some Fundamentals of Tin-Bismuth Metallurgy and Electromigration
09/24/2024 | Prabjit Singh, Raiyo Aspandiar, Haley Fu, and L. A. SwaminathanNear-eutectic tin-bismuth alloy is a strong contender as the solder of choice for low-temperature electronic assembly applications. This article will describe the recent significant developments by the iNEMI project team on the understanding of the electromigration behavior of Sn-Bi solder which has a unique physical metallurgy and electromigration behavior quite different for that of Sn-Ag-Cu (SAC) solder and other solders in common use today.
iNEMI Packaging Tech Topic Webinar: Packaging Interconnect Material Technology Series
09/19/2024 | iNEMIThe International Electronics Manufacturing Initiative (iNEMI) continues its Packaging Interconnect Material Technology Series with a webinar on Transient Liquid Phase (TLP) Bonding for High-Temperature Soldering Processes.