-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueMechatronics
Our expert contributors discuss the advent of mechatronics in PCB design, the challenges and opportunities this creates for circuit board designers, and the benefits—to the employee and the company—of becoming a mechatronics engineer.
Creating a Culture of Collaboration
PCB designers could learn quite a bit from NASA and the private companies that develop spacecraft: Every one of these vehicles is a testament to the value of collaboration among disparate stakeholders. Without a collaborative culture, the rocket might never get off the ground.
Breaking High-speed Material Constraints
Do you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems. Learn more in this issue.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Q&A: The Learning Curve for Ultra HDI
October 20, 2022 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 2 minutes
![](https://iconnect007.com/application/files/5416/3116/7160/tara_dunn250.jpg)
For this issue on ultra HDI, we reached out to Tara Dunn at Averatek with some specific questions about how she defines UDHI, more about the company’s patented semi-additive process, and what really sets ultra HDI apart from everything else. Do designers want to learn a new technology? What about fabricators? We hope this interview answers some of those questions that you may be having about these capabilities and what it could mean for your designs.
Q: How do you define ultra HDI? What is the cutoff in mils or microns?
A: That is an excellent question. At this point I think it means different things to different people depending on where their current HDI capabilities are. IPC has created an ultra HDI working group and I believe the definition they are working with is that to be considered ultra-HDI, a design needs to include one or more of these parameters: Line width below 50 µm, spacing below 50 µm, dielectric thickness below 50 µm, and microvia diameter below 75 µm.
Q: Averatek has developed the A-SAP™ semi-additive process, which can produce traces down into the UHDI space. Can you clear up the differences between mSAP and A-SAP, and what this means to designers and design engineers?
A: In general, SAP, or a semi-additive process, is a process that starts with a very thin layer of copper and then builds the trace patterns from there. One common differentiating factor in these two approaches to SAP is the starting copper thickness. Typically, copper thickness that is 1.5 microns or above would be considered mSAP, or a modified semi-additive process. Because the copper is a little thicker than other SAP processes, it requires more etching, which can have impacts on trace width and space and also the sidewalls of the trace. This process can typically provide features as small as 30 microns in highly specialized facilities that are running extremely high-volume manufacturing. This technology is commonly seen in our smartphones.
Averatek’s A-SAP begins with a much thinner electroless copper, typically 0.2 µm and this copper thickness, or thinness if you will, enables the fabricator to produce much finer feature sizes. The technology is capable of traces and spaces as small as 1 micron if the fabricator has advanced imaging equipment. Typically, PCB fabricators have equipment that can image traces to 12.5 µm today. There are also signal integrity benefits to this process. Because the base copper is so thin, there is minimal impact on the trace sidewalls, and greater control to line width resulting in impedance control tolerance improvements.
One other difference between the mSAP and A-SAP technologies is in the ratio of trace height to trace width; mSAP processes allow a 1:1 ratio of height to width and A-SAP traces can be produced with aspect ratio of 2:1 or greater. For example, a 25 µm wide trace could be 40 µm tall. This has gotten a lot of attention from a signal integrity perspective.
To read this entire article, which appeared in the October 2022 issue of Design007 Magazine, click here.
Suggested Items
Trouble in Your Tank: Materials for PWB Fabrication—Drillability and Metallization
07/16/2024 | Michael Carano -- Column: Trouble in Your TankLaminate materials are the building blocks on which printed circuit boards are manufactured. Circuit board designers rely on the critical electrical properties of the materials to design the interconnects, and with the drive toward IoT (internet of things), autonomous driving, and virtual and augmented reality, material properties take on a very high level of importance.
Beyond Prepreg: The Glassless ‘Revolution’
06/25/2024 | Marcy LaRont, PCB007 MagazineAs our industry rallies around the call to action for HDI and UHDI, we find unparalleled and myriad laminate options. This abundance is rivaled only by the question surrounding them: Can they measure up to the high technology packaging demands required in our near future? Unsurprisingly, recent developments in FR-4-esque materials for high-speed and high-density designs, as well as newer, glassless technology for replacing traditional glass-impregnated laminates and prepreg, are garnering much interest. I caught up with Alun Morgan, technology ambassador for Ventec International Group, to ask about the impending “glassless revolution” and how it’s poised to solve some of our manufacturing challenges.
Connect the Dots: Designing for Reality—Lamination and Materials
06/19/2024 | Matt Stevenson -- Column: Connect the DotsAs many of you have likely figured out, I am quite passionate about the subject of designing PCBs for the reality of manufacturing. I wrote a book about it and I participate in an I-Connect007 On the Line with… podcast series dedicated to the subject. This companion article will focus on multilayer lamination, keeping the bigger picture in mind: Realistic PCB designs should prioritize manufacturability and reliability of the PCB as well as meet the other design requirements. So, one must account for the production variables associated with individual manufacturing partners.
Day 2: A Full Day at the EIPC Summer Conference
06/19/2024 | Pete Starkey, I-Connect007Editor's note: This is the third and final report from the EIPC Summer Conference. It was a bright and early start to the second day of the 2024 EIPC Summer Conference at the European Space Centre, Noordwijk, The Netherlands, June 4-5. A short journey by bus from the hotel in Leiden and our security passes from the day before got us through the gate and to our seats in the Newton Room for Session 4, “Material Studies,” moderated by Martyn Gaudion.
Looking Into Space: EIPC Summer Conference, Part 2
06/17/2024 | Pete Starkey, I-Connect007“Innovative Development of PCB Technology and Design” was the theme of the second session of the 2024 EIPC Summer Conference, June 4-5, at the European Space Centre, Noordwijk, The Netherlands.