-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Growing Industry
In this issue of PCB007 Magazine, we talk with leading economic experts, advocacy specialists in Washington, D.C., and PCB company leadership to get a well-rounded picture of what’s happening in the industry today. Don’t miss it.
The Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Plating on Silver: What’s Old is New Again
July 7, 2022 | Denis Jacques, Technic Inc.Estimated reading time: 2 minutes
About three decades ago, immersion silver, a nitrate-based process, gained a lot of market share in the world of PCB final finishes. More economical than ENIG, flat, solderable, and conductive, it had everything going for it—everything but corrosion resistance in a harsh environment, that is.
Champagne voids were also an issue, along with line reduction. But the worst drawback, the characteristic that made the part short over time, was creep corrosion. A build-up of copper sulfide salt that grows in contact with a sulfur-rich environment, heat, and moisture resulted in failures in the field. This was enough to scar the process for good.
The market today for silver as a final finish is pretty meager and therefore does not justify much research. Fortunately, there is an alternative immersion silver, originally developed for other applications, that has proven to be a reliable solution. Immersion silver is nitrate-free, slightly alkaline, and deposits a slow, pore-free pure silver deposit. I had a strong feeling that this process would be a solid alternative to nitrate-based chemistry, yielding the benefits without the drawbacks.
Work started about 10 years ago with this product, on a very limited basis, because as mentioned before, the interest in silver is just not there. One of our customers raised the fact that their silver was acting somehow galvanic, and some isolated lines were reduced. The customer works in the RF field, and this was a major issue for them. I offered to test this bath, feeling that it could be a solution to the problem.
We had nitrate-free silver, which builds up about 10–15 microinches of silver in five minutes, so we tried simple tests with it. To our surprise, it solved all their issues, and they became an instant customer for this silver. They had had ongoing champagne voids and line reduction issues, and this silver solved that for them.
Strong on that success, we made a few installations where those issues were identified. As I mentioned, the silver market was slow, and we did not push because we did not know of any corrosion benefit yet. The nitrate-based process can deposit up to 20–30 microinches in one minute, and for us, that is the main issue. We felt that thinner, pore-free silver had to be better than thicker, fast deposited silver.
We had in mind to do a side-by-side bench comparison of these two silvers. The nitrate base is still dominating the market and is also directly related to the minuscule market share of silver as a final finish. Then the pandemic hit, and I had a lot of free time to involve myself in that long-desired bench comparison study.
Some material manufacturers had begun to share their findings on 5G requirements and, based on the requirements of high-frequency PCBs, it looked like silver was the way to go. To make a long story short, high frequencies travel on the surface, and silver is practically as good as copper at precluding signal loss. Signal loss was the main problem for 5G applications as the component will stop working.
Compensating for insertion loss requires a more sophisticated material, or heat-resistant components, or signal boosters, all of which lead to higher costs to accommodate ENIG.
To read this entire article, which appeared in the June 2022 issue of PCB007 Magazine, click here.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.