Target Condition: Are Autorouters Friend or Foe?
Fresh PCB Concepts: Assembly Challenges with Micro Components and Standard Solder Mask Practices
Elementary Mr. Watson: Retro Routers vs. Modern Boards—The Silent Struggle on Your Screen
Effective Decoupling Radius
May 6, 2015 | Kirk Fabbri, KPST Engineering ConsultingEstimated reading time: 1 minute
Power distribution networks (PDN) are becoming an important topic. Many engineers are finding that properly designing the power supplies and providing adequate decoupling for devices is a challenge, especially since devices are switching faster and dimensions are shrinking. Engineers often focus on discrete decoupling capacitors placed local to switching devices in hopes of providing the required capacitance for these high current demands. One of the more overlooked items of the power distribution system is the PCB, and how it contributes to the power distribution system’s ability to decouple the switching devices. The following experiment will outline a basic principle that should be in mind when designing a stack-up and PDN.
Basic PDN Model
A basic PDN includes the voltage regulator model (VRM), the discrete decoupling capacitors, the PCB, and any on-die capacitance formed on the IC or device. Each one of these components could be written about separately, but it is the PCB that will be focused on; specifically the effective decoupling radius.[2]
When a device is active, it will require current. The type of device (process size), load on the I/O drivers, and how the device is operated, all have an effect on the current required, among others. When the device demands current, it flows through the complex impedance of the PDN and causes a ripple voltage to appear. This transient current is drawn from a variety of sources including the local on-die decoupling capacitance, the PCB, the discrete capacitors, and finally the VRM.[1] The edge rate of this switching current is extremely important when trying to calculate how effective the PDN will be in suppressing the ripple voltage. The switching edge can be dissected into a variety of harmonic sine waves at decreasing amplitude described by a Fourier series equation. It is here that we discover the importance of the PCB, and its role in the PDN.
The simplest way to represent a PCB is a distributed RLC network. Capacitance is formed by the copper layers and the dielectric between them. Inductance is formed by the loop area between the layers, and the resistance is formed by the cross sectional area and length of the copper planes.
To read this article from the April 2015 issue of The PCB Design Magazine, click here.
Share on:
Suggested Items
The Evolution of Picosecond Laser Drilling
06/19/2025 | Marcy LaRont, PCB007 MagazineIs it hard to imagine a single laser pulse reduced not only from nanoseconds to picoseconds in its pulse duration, but even to femtoseconds? Well, buckle up because it seems we are there. In this interview, Dr. Stefan Rung, technical director of laser machines at Schmoll Maschinen GmbH, traces the technology trajectory of the laser drill from the CO2 laser to cutting-edge picosecond and hybrid laser drilling systems, highlighting the benefits and limitations of each method, and demonstrating how laser innovations are shaping the future of PCB fabrication.
Day 2: More Cutting-edge Insights at the EIPC Summer Conference
06/18/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) summer conference took place this year in Edinburgh, Scotland, June 3-4. This is the third of three articles on the conference. The other two cover Day 1’s sessions and the opening keynote speech. Below is a recap of the second day’s sessions.
Day 1: Cutting Edge Insights at the EIPC Summer Conference
06/17/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) Summer Conference took place this year in Edinburgh, Scotland, June 3-4. This is the second of three articles on the conference. The other two cover the keynote speeches and Day 2 of the technical conference. Below is a recap of the first day’s sessions.
Preventing Surface Prep Defects and Ensuring Reliability
06/10/2025 | Marcy LaRont, PCB007 MagazineIn printed circuit board (PCB) fabrication, surface preparation is a critical process that ensures strong adhesion, reliable plating, and long-term product performance. Without proper surface treatment, manufacturers may encounter defects such as delamination, poor solder mask adhesion, and plating failures. This article examines key surface preparation techniques, common defects resulting from improper processes, and real-world case studies that illustrate best practices.
RF PCB Design Tips and Tricks
05/08/2025 | Cherie Litson, EPTAC MIT CID/CID+There are many great books, videos, and information online about designing PCBs for RF circuits. A few of my favorite RF sources are Hans Rosenberg, Stephen Chavez, and Rick Hartley, but there are many more. These PCB design engineers have a very good perspective on what it takes to take an RF design from schematic concept to PCB layout.