-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Growing Industry
In this issue of PCB007 Magazine, we talk with leading economic experts, advocacy specialists in Washington, D.C., and PCB company leadership to get a well-rounded picture of what’s happening in the industry today. Don’t miss it.
The Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Improved Design of Dry Film Resist Laminator for Optimal Transfer of Micron-sized Features
August 24, 2015 | Fred Long, Matrix ElectronicsEstimated reading time: 5 minutes
Introduction
Since the inception of dry film lamination, the process of squeezing two hot rolls at their end axis points has caused roll bending. An innovative process has now been developed whereby the film is attached with a process that minimizes this issue and provides optimal, evenly dispersed heat and pressure across the entire surface of the panel. This simple and elegant design will ensure that the integrity of the resulting image will be ideal, as measured by the continuity of the resulting transferred traces and features.
Electronic printed circuit board packaging is reaching its limit because of micron requirements, defined here as features below 5 mils (0.005”), or below 125 microns.
Over the years, front-end activities in the PCB manufacturing shop have changed from manual artwork to digitized input to vector photoplotting to phototools generated from digital/raster input. Today, digital imaging produced by either laser or projection techniques has solved the micron situation with great success.
So with our front-end issues resolved, we move to the next and key intermediate process step. This is arguably one of the most important PCB processes: the application of dry film resist to the copper surface.
Historically, here is where we continue to see faulty transfer of the original image to the copper surface. The current (and old) way of pressing down the dry film is simply inadequate. Rolls bend, resulting in low pressure in the central areas of the copper-clad panel. This can cause open circuit situations due to breaks in the copper images. These are, of course, most evident and critical on micro features (i.e., less than 0.005” [5 mil]).
The industry has made great strides in the past 20 years, but we still continue to look for ways to deal with the micron issue throughout the fabrication process. One at a time, we see these obstacles being corrected. This article highlights one of the most important steps to continue the goal of attaining optimal yield and success with the available tools.
The Innovation
Consider that we have just been handed an outstanding direct imaging database, almost perfect in every way with panel and feature dimensions meeting the most stringent micron requirements. Better yet, if environmental factors cause unexpected material movement, we can alter the data base with precise micron adjustments.
Our industry has been plodding along, not paying attention to a serious compromise since the inception of dry film lamination. From the 1950s–1980s this was not a problem, but with time, those micron requirements have been speeding our way.
While it appeared to be a perfectly adequate solution for applying dry film to copper, we have accepted the squeezing of two hot rolls at their axis ends to be our process standard (Figure 1).
Figure 1: Roll bends.
Figure 2: Pressure comparisons.
Note: Figures 1 and 2 are historical data seen for several years in various publications. The information has always been acknowledged but never rectified—until now.
Figure 1 is an exaggerated graphic that shows how the rolls will bend no matter how much pressure is applied at the ends. It is pure physics, and in fact, the more pressure applied, the worse the bending. If one were to measure the pressure along the length of the roll, we would see high pressure being applied to the ends and the pressure would become less as we move toward the center. The higher pressure at the ends, combined with certain types of softer dry films, will most likely provide proper film adhesion with acceptable film conformance. However, moving toward the center of the rolls, and with certain types of films, there can be literally no pressure (Figure 2).
Again, this worked well when features were in the 10 mil (0.010”) range, but as features began to reach our micron status, dry film adherence to the copper was random and without conformity. More importantly, if the copper surface has small imperfections (pits and dents), dry film needs to be pressured into those areas with firm and predictable results, otherwise the resulting image on the dry film will not transfer properly, and in most inner layer cases, will cause open circuits.
Further, as equipment reaches the end of its useful life, machine tolerances begin to play havoc with our most important requirement—transferring micron features.Page 1 of 2
Suggested Items
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?