Estimated reading time: 5 minutes

Configure to Order: Different by Design

Perhaps in the future, sentient robots look-ing back at humans today will consider that we were a somewhat random bunch of people as no two of us are the same. Human actions and choices cannot be predicted reliably, worse even than the weather. As with any team however, our ability to rationalize in many different ways in parallel is, in fact, our strength, creating a kind of biological “fuzzy logic.” Robots will have to cope with mankind’s wishes for differentiation, no matter how illogical that may be. Rather than repetitive automation, the Industry 4.0 computerization concept has been created to find efficiency in automated randomness. The crux of such a process is the ability to be prepared for, and to be able to manage, the increasing mix of products and their variants effectively, just as smoothly as if factories were producing in high volume. When considering Industry 4.0 therefore, being able to digitally configure to order (CTO), rather than having to be responsible for hundreds or thousands of individual bill of materials (BOMs), in a simple and effective way is an essential, critical business need.

Automation has been a key element since the start of the third industrial revolution, where electrical systems and controllers have been running machinery designed to replace human manual dexterity. Until quite recently, automation has been rather dumb. Simple automation was dominant where machines simply followed a set of sequential instructions, or, in the case of assembly robots, copied a series of movements. More evolved automation can apply alterations and corrections based on, for example, the processing of visual checks on SMT machines, which correct the position and orientation of materials picked up or positioned for placement. The challenge for the creation of the vast majority of automated processes was made very much easier by the notion of mass production, where once set up, the automation would simply repeat what it was doing in a very efficient way, with very high equipment utilization. Unfortunately, the heyday of repetitive high-volume manufacturing for most of us has passed.

It seems ironic that automation has played the initial part in the downfall of mass-production itself. Adopting automation meant that the quantity of products made could be increased drastically over manual production lines. This meant that the market for such products expanded. Requirements in expanded markets meant that there needed to be different versions made, for example with different electricity or communication standards, including of course human language. The concept of variants was born. Once established, marketing teams got involved, using variants to find ways of target-ing against competitor’s products, making lower cost versions, higher featured versions. Any company could then target increasingly well-defined niches of customer need with exactly the right cost-effective product. After marketing, came fashion. Technology has become fashionable, creating the need, for example, in personal devices such as cell-phones, to be available in many different sizes, colors and styles. Perhaps as an extreme example, but genuine nonetheless, a specific original design of mobile phone is now manufactured with thousands of individual variants, depending on feature level, resource level, wireless options, software options, language, service provider, colors, etc. Keeping track of which phone is which during manufacturing is an absolute nightmare. Most of the variants look the same throughout most of the processes, but have different assembly combinations, including subtle differences in electronic component placement positioning. The worst aspect of this is yet to come. Since there are so many variants, the cost of storage of semi-complete and completed products has increased in line with the number of variants being produced. In most cases, the business demand has been to avoid stock of products as far as possible. The number of days of stock throughout the distribution chain has typically shrunk from being many months, to a few days at most. For manufacturing operations that are remote from their markets, such as China, the reduction can only be achieved by air-freight rather than sea-freight, increasing distribution costs and environmental impact. Companies that manufacture close to their markets, typically those remaining in the West, are pushed to be almost “make to order” so as to keep needless investment of stock to an absolute minimum. In-factory warehousing is included. The opportunity for manufacturing to smooth the effect of high product mix on the lines by creating stockpiles in the warehouse is rapidly running out. The reality now must be faced. Manufacturing must be capable of producing multiple configurations with complete control and without any loss of productivity. Those companies that can achieve this are surely the companies that will succeed, having reduced the extortionate operational overhead of mixed and low-volume production to an absolute minimum. This is the condition that Industry 4.0 achieves through the use of computerization.

When considering implementation of Industry 4.0 solutions, following the hype in the market, attention typically is focused on the need for communication between machines on the shop-floor. Knowing what is currently executing and the status of each process in the factory, as well as all the related resources and support operations, provides critical information for Industry 4.0 computerized management systems. This includes work-order creation and assignment, as well as the control and planning of related resources and support operations. What is often neglected however until much later in the process, is the management and control of the engineering definitions of products and related variants that are to be made in this ultra-flexible factory. Engineering control is quite a challenge considering the many tens, hundreds or indeed thousands of products and variants that can potentially be live in production in a single factory at any time. The management of the precise engineering data, which includes visual aids and documentation, to be supplied to all processes exactly when needed can quickly become an extreme drain on engineering resource. Add to this the need for conformance, where every set of engineering data, whether comprising a set of machine instructions, or an ISO controlled operation standard for a manual process, needs to be issued and confirmed into place prior to specific execution of a work-order.

Continue reading this article in the January 2018 issue of SMT007 Magazine.