-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueAdvanced Packaging and Stackup Design
This month, our expert contributors discuss the impact of advanced packaging on stackup design—from SI and DFM challenges through the variety of material tradeoffs that designers must contend with in HDI and UHDI.
Rules of Thumb
This month, we delve into rules of thumb—which ones work, which ones should be avoided. Rules of thumb are everywhere, but there may be hundreds of rules of thumb for PCB design. How do we separate the wheat from the chaff, so to speak?
Partial HDI
Our expert contributors provide a complete, detailed view of partial HDI this month. Most experienced PCB designers can start using this approach right away, but you need to know these tips, tricks and techniques first.
- Articles
- Columns
Search Console
- Links
- Media kit
||| MENU - design007 Magazine
Rigid-flex Design Guidelines
September 27, 2023 | Cherie Litson, CID+, Litson1 ConsultingEstimated reading time: 4 minutes
Rigid-flex circuits are unique structures; part rigid board and part flex, they’re increasingly working their way into many of the electronic devices we use every day.
There have been many advances in rigid-flex lately as more companies find themselves exploring this technology. So, before I started writing this article about rigid-flex design, I double-checked a few things. Fortunately, there is plenty of rigid-flex information available on a variety of great websites that we all know and trust. So, here’s a quick look at some of the principles of rigid-flex design.
Rigid board designers who consider entering the rigid-flex arena typically have a handful of questions. One of the most obvious is, “Why do we need rigid-flex anyway?” If we just need a way to fit circuitry into a case and it will stay that way, rigid-flex will work fine. But if the board will be moving on a regular basis during operation, then opting for just flexible circuits or attaching flex to a traditional rigid board is a better way to go.
Another common question is, “How does my PCB layout software work with curves and hatched planes?” There are a lot of curved traces and hatched planes in flex circuits. If it’s a hassle to create a curved trace, you may need a different software package that is optimized for flex and rigid-flex design. Many of today’s EDA tools are set up for rigid-flex design.
Rigid-flex boards use the same materials as any rigid board. One way to do this is by creating the flex portion along with the layers of the rigid board, and use a delamination process to remove any unwanted layers. No components are mounted on the flex portion of the board. One layer is used for the return and the other layer is used for your signals. The return is commonly a GND plane and hatched in the flex area of the board. Vias are not usually placed in this area either but may be used if needed.
Another rigid-flex approach is to first create a flex board and then laminate or adhere a rigid board (or just a stiffener) to the flex. This is done when you need more signal layers in the flex portion, the flex needs to be longer, and/or it needs to withstand multiple flexing without breaking. The rigid portions are processed separately and have the components assembled to them. In general, components should not be mounted on the flex portion. Flexing solder joints is just a bad thing.
Now you’ve got the basics, what’s next? Here are a few guidelines, in no particular order:
- Layer stackup: Keep the flex layers to a minimum of two for increased mechanical flexibility and reduced costs.
- Electrical design constraints: What needs to be on the flex and what doesn’t? Trace widths may need to vary. They may need to be very long. Make sure that the signals can handle these conditions. Also, designers should have a good understanding of the heat sinking capabilities of the flex portion.
- Mechanical design constraints: You will need more clearance to the edges of the board, cutouts, slots, other traces, etc., as well as more space around bends and corners. Any slots or holes that must be cut will need “relief” features so that the material doesn’t tear.
- Component placement and finishes: As I mentioned, components in general, should not be mounted on flex, but there are exceptions. Some components can be mounted on the flex portion with a stiffener material attached beneath them to prevent solder joint breakage. The finish used to protect the open copper traces is usually an overlay material or a thicker solder mask—not LPI. Both of these have larger clearance areas around the components. Conformal coatings can be used to protect the bare copper after soldering.
- Testing and verification: Because of the unique structure of rigid-flex circuits, testing and verification are critical parts of the process. Test points must be strategically placed, not too close to edges or components, and not covered by solder mask. Ask your fabricator for more information.
Rigid-flex Resources
IPC has a variety of great resources and specific industry standards on its website. IPC-6013 Qualification and Performance Specification for Flexible Printed Boards, features a treasure trove of information. IPC-4201 through IPC-4204 cover many of the base materials used for flex circuits. IPC-4562 covers copper foils and IPC-SM-840 defines the masks that can be used.
Once you’ve defined what you need in your rigid-flex design, find a flex fabricator you can work with to get the job done. Most of the guidelines listed by fabricators online focus on the company’s limitations. They all have different capabilities, so be sure to match your needs with their limits for the best cost return. Pay close attention to their “standard” feature sizes, not the “highest-end capability.” If your electrical and mechanical constraints are critical to your design, be sure to have a conversation with the production engineer at the facility. This will help you and the fabricator.
Your EDA software company should also have an online section titled “How to Layout a Flex Design.” These are great resources and worth looking at. If you don’t like your software’s approach to rigid-flex, check out some of the videos from the other software companies. You might find something you didn’t think of before.
Cherie Litson is a PCB design and engineering consultant.
This article originally appears in the September 2023 issue of Design007 Magazine.
Suggested Items
Flex Completes Acquisition of Crown Technical Systems
12/04/2024 | PR NewswireFlex recently announced that it has completed its previously announced $325 million all-cash acquisition of Crown Technical Systems, a leader in fully integrated power distribution and protection systems.
Flex PCB Design Best Practices with Dave Lackey
12/04/2024 | Brittany Martin, I-Connect007David Lackey, a flex circuit expert at American Standard Circuits, speaks about the advantages and challenges of designing with flexible and rigid-flex PCBs. He also discusses how consulting before the design phase can save time and costs by avoiding manufacturing issues and highlights the reliability and packaging benefits of flex technology, especially for compact designs in sectors like aerospace.
Flexible Electronics Market to Reach $75.04 Billion by 2032
12/03/2024 | Globe NewswireThe SNS Insider report indicates that,“The Flexible Electronics Market Size was valued at USD 32.65 Billion in 2023 and is expected to reach USD 75.04 Billion by 2032 and grow at a CAGR of 9.72% over the forecast period 2024-2032.”
ULVAC Launches New Deposition System for Semiconductor Applications
12/02/2024 | JCN NewswireULVAC, Inc. has started accepting orders for the ENTRON-EXX, a new multi-chamber deposition system for semiconductor applications. The ENTRON-EXX builds on the proven productivity and flexibility of its predecessor, the ENTRON-EX W300, while offering enhanced data intelligence and expandability.
Flex Announces Kevin Krumm as Chief Financial Officer
11/27/2024 | FlexFlex announced that Kevin S. Krumm will join the company as Chief Financial Officer (CFO), effective January 6, 2025. He will succeed Jaime Martinez, interim CFO, who will remain with Flex and support a smooth transition.