Elementary Mr. Watson: Routing Hunger Games—May the Traces Be Ever in Your Favor
Target Condition: Floor Planning Without a Floor
Happy’s Tech Talk #42: Applying Density Equations to UHDI Design
If You Can Define It Right, You Can Design It Right
December 5, 2024 | Andy Shaughnessy, Design007Estimated reading time: 1 minute
Design engineer Chris Young is known for his optimized design process. As lead hardware engineer with Moog Space and Defense Group and owner of Young Engineering Services, Chris collects data like it’s going out of style, and he leaves nothing to chance.
With that in mind, I asked Chris to discuss his views on rules of thumb—which ones work, which ones should be avoided, and how rules fit ideally into the PCB design process.
Andy Shaughnessy: I know that you’ve spent a lot of time and effort over the years dialing in your design process. How do you use rules of thumb in your design cycle?
Chris Young: I use purpose-driven rules of thumb that produce practices that reduce risk and drive a desired outcome. I am much less concerned about using a specific PCB stack-up than producing a solution that works and meets requirements.
Shaughnessy: What are some of the rules of thumb that you use regularly, and why?
Young: Rule No. 1: If you can define it right, you can design it right.
Spend time up front developing requirements that can be used to guide your design to success. The lack of requirements in a project lead to technical ambiguity that is too often stop-gapped with assumptions. These assumptions lead to design errors that result in technical debt or design spins that cost money. The old adage of “measure twice, cut once” still applies. I recommend the INCOSE Guide to Writing Requirements (incose.org) for anyone interested in learning more about developing clear, actionable requirements.
To read this entire conversation, which appeared in the November 2024 issue of Design007 Magazine, click here.
Share on:
Testimonial
"The I-Connect007 team is outstanding—kind, responsive, and a true marketing partner. Their design team created fresh, eye-catching ads, and their editorial support polished our content to let our brand shine. Thank you all! "
Sweeney Ng - CEE PCBSuggested Items
Mastering PCB Floor Planning
08/28/2025 | Stephen V. Chavez, Siemens EDAPlacement of PCB components is far more than just fitting components onto a board. It’s a strategic and critical foundational step, often called “floor planning,” that profoundly impacts the board’s performance, reliability, manufacturability, and cost. Floor planning ties into the solvability perspective, with performance and manufacturability being the other two competing perspectives for addressing and achieving success in PCB design.
Elementary Mr. Watson: Routing Hunger Games—May the Traces Be Ever in Your Favor
08/26/2025 | John Watson -- Column: Elementary, Mr. WatsonI’d like to share a harsh truth, and I say this as a friend: PCB designers are often their own worst enemy. It’s rarely the complexity of the circuit, the last-minute changes from mechanical, the limited enclosure space, or the ever-expanding list of design rules that send projects to the dust heap of failed boards. More often, it's our own decisions, made too quickly and narrowly, and with too little foresight, that sabotage an otherwise good design.
Target Condition: Floor Planning Without a Floor
08/27/2025 | Kelly Dack -- Column: Target ConditionBy a show of hands, how many PCB designers have been asked to start a layout without a board outline, keep-out zones, or even height constraints? How many have had to work within a specific enclosure before the schematic was finalized? If this sounds familiar, you're not alone. Starting a PCB layout without critical constraints is like hiring an interior designer to buy furniture and carpet for a house you haven’t even purchased yet, or, even worse, trying to fit four bedrooms' worth of furniture in a one-room cabin.
I-Connect007 Editor's Choice: Five Must-Reads for the Week
08/22/2025 | Andy Shaughnessy, I-Connect007In this week’s roundup, we have a variety of articles covering design, manufacturing, sustainability, and, of course, tariff negotiations. We have a milestone anniversary to celebrate as well, with Dan Beaulieu about to publish his 1,000th column. When does Dan even sleep? Here’s to hoping that we have 1,000 more weeks of "It’s Only Common Sense."
New Episode Drop: MKS’ ESI’s Role in Optimize the Interconnect
08/26/2025 | I-Connect007In this latest episode, Casey Kruger, director of product marketing at MKS’ ESI, joins On the Line With… host Nolan Johnson to share how CO₂ laser technology delivers faster, more accurate vias in a smaller, more energy-efficient footprint.