Elementary Mr. Watson: Ensuring a Smooth Handoff From PCB Design to Fabrication
The Shaughnessy Report: Breaking Down the Language Barrier
Connect the Dots: Designing for Reality—Routing, Final Fab, and QC
IPC Standards Committee Reports – Packaged Electronic Components, Flex Circuits, High Speed/High Frequency, Rigid Printed Boards
December 7, 2015 | IPCEstimated reading time: 4 minutes
Packaged Electronic Components
The B-11 3-D Electronic Packages Subcommittee continued work on IPC-7091, Design and Assembly Process Implementation of 3-D Components. There has been significant interest in this standard from both the military and commercial markets, and the subcommittee is ensuring groups doing similar work are included in the efforts for IPC-7091.
Flexible Circuits
The D-11 Flexible Circuits Design Subcommittee met to advance the Working Draft to IPC-2223D, Sectional Design Standard for Flexible Printed Boards. The group reviewed and approved new drawings depicting flexible cross-sectional construction examples and unbonded flex cross-sectional constructions for rigid-flex designs. The group also reviewed new content addressing the factors that affect impedance and capacitance control for flex and rigid-flex printed board applications so as to mitigate signal integrity issues.
The D-12 Flexible Circuits Performance Subcommittee met to advance the Working Draft to IPC-6013D, Qualification and Performance Specification for Flexible Printed Boards. The group also reviewed a cross-sectional illustrations that address voiding or delamination in the transition zone between flexible material and rigid material. The group also reviewed examples of anomalies in flexible printed board assemblies (e.g. kinks in the ribbon cable following assembly operations) and agreed to submit recommendations to the IPC 7-31b task group for addressing these issues in a future revision to IPC-A-610, Acceptability of Electronic Assemblies.
The D-13 Flexible Circuits Base Materials Subcommittee began review and updating of IPC-4202A to ultimately revise it to B revision.
The D-15 Flexible Circuits Test Methods Subcommittee began to review all flexible circuits test methods for relevance to all materials, printed boards and design standards. Most if not all test methods that apply to old flexible circuits (those that begin with “FC” are likely to be obsolete and will likely be archived.
Page 1 of 3
Share on:
Suggested Items
Würth Elektronik Now an Infineon ‘Preferred Partner’
03/13/2025 | Wurth Elektronik eiSosWürth Elektronik, one of the leading manufacturers of electronic and electromechanical components, is broadening its collaboration with semiconductor manufacturers.
Elementary Mr. Watson: Ensuring a Smooth Handoff From PCB Design to Fabrication
03/13/2025 | John Watson -- Column: Elementary, Mr. WatsonAt the 2020 Tokyo Summer Olympics, the U.S. men's 4x100-meter relay team had high hopes of winning a medal. The team comprised some of the fastest sprinters in the world, but something went wrong. In a relay, four runners must smoothly pass their baton to the next runner inside a zone on the track. If a runner drops the baton or it’s passed outside the zone, the team risks disqualification. The U.S. team’s pass between the second and third runner was messy, slowing them down. By the time the last runner received the baton, the team had lost too much time. They finished sixth in their heat and didn’t qualify for the final.
Ventec International Group Announce Launch of VT-47LT IPC4101 /126 Prepreg for HDI
03/12/2025 | Ventec International GroupVentec International Group announce launch of VT-47LT IPC4101 / 126 Prepreg. Are Microvia Failures Plaguing Your HDI Any Layer Designs? High-density interconnect (HDI) designs are pushing the envelope - higher layer count HDI relies on complex microvia designs: skip vias, staggered microvias, and stacked microvias in sequential laminations.
TI Introduces the World's Smallest MCU, Enabling Innovation in the Tiniest of Applications
03/12/2025 | PRNewswireTexas Instruments (TI) introduced the world's smallest MCU, expanding its comprehensive Arm® Cortex®-M0+ MSPM0 MCU portfolio. Measuring only 1.38mm2, about the size of a black pepper flake, the wafer chip-scale package (WCSP) for the MSPM0C1104 MCU enables designers to optimize board space in applications such as medical wearables and personal electronics, without compromising performance.
Speaking the Same Language as Your Fabricator
03/12/2025 | Andy Shaughnessy, Design007 MagazineWe do indeed have a failure to communicate; designers and fabricators often seem to be talking past each other, which can lead to jobs being put on hold. We asked Jen Kolar, VP of engineering for Monsoon Solutions, and columnist Kelly Dack to share their thoughts on ways that we can break down the communication barrier between design and fabrication. As they point out, a design kickoff checklist and a solid review process can be invaluable tools in a designer’s toolbox.