-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueSilicon to Systems: From Soup to Nuts
This month, we asked our expert contributors to weigh in on silicon to systems—what it means to PCB designers and design engineers, EDA companies, and the rest of the PCB supply chain... from soup to nuts.
Cost Drivers
In this month’s issue of Design007 Magazine, our expert contributors explain the impact of cost drivers on PCB designs and the need to consider a design budget. They discuss the myriad design cycle cost adders—hidden and not so hidden—and ways to add value.
Mechatronics
Our expert contributors discuss the advent of mechatronics in PCB design, the challenges and opportunities this creates for circuit board designers, and the benefits—to the employee and the company—of becoming a mechatronics engineer.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
3D Electromagnetic Analysis
August 22, 2023 | Yuriy Shlepnev, SimberianEstimated reading time: 1 minute
![](https://iconnect007.com/application/files/7016/3125/7306/Yuriy-Shlepnev-300.jpg)
Data rates in PCB interconnects are increasing in all signaling protocols (PCIe, DDR, GDDR, Ethernet, USB, SAS, InfiniBand, CEI, OIF, 5G). Most of those high-speed signaling standards have one-lane data rates over 6 Gbps (GT/s) and some up to 112 Gbps with signal spectrum in microwave and even millimeter wave bandwidths. Design of compliant interconnects at these data rates cannot simply rely on geometrical rules or rules of thumb. Signal distortion by reflections, dissipation and crosstalk can cause interconnect performance degradation or even failure. To avoid it, signal integrity compliance analysis and possible interconnect optimization is required.
Our software provides 3D electromagnetic analysis of PCB and packaging interconnects. It can be used for pre-layout design (stackup exploration, via hole design) and post-layout interconnect compliance analysis and optimization. Simbeor ensures the accuracy of the models by using advanced algorithms for 3D full wave analysis, benchmarking, and experimental validation. Simbeor and the “sink or swim” interconnect design process remove all uncertainties and guarantee the first pass design success. Most importantly, it lets you solve electromagnetic signal integrity problems at a relatively low cost and with extreme ease. You don't need to be an expert in signal integrity or have a PhD in electromagnetics to use it.
The first version was introduced in 2007. It was the first electromagnetic tool designed specifically for PCB designers and signal integrity engineers. Since then, its evolution is a chain of innovations in interconnect analysis and validation. In the past three years, with the major part of the work completed in "self-isolation," our team has elevated the tool to a new level.
Our software development kit was introduced for design exploration, machine learning, and for possible integration into other tools. Post-layout geometry processing, visualization and model building were accelerated orders of magnitude. Electromagnetic analysis was also accelerated orders of magnitude with the domain decomposition technique. We had enough time—there were very few distractions—and sufficient expertise to re-think and re-design the post-layout process, making it suitable not only for SI engineers, but for any PCB designer.
To read this entire article, which appeared in the August 2023 issue of Design007 Magazine, click here.
Suggested Items
I-Connect007 Editor's Choice: Five Must-Reads for the Week
09/06/2024 | Nolan Johnson, I-Connect007This week’s Top 5 starts with steps you can take to cultivate a culture of thriving. We also have bullish news from the global semiconductor sector, advice on how to tease out hidden cost drivers during the PCB design cycle, how the Altium-Ansys collaboration will affect design, and Happy Holden’s version of Occam’s Razor—three simple tools to keep your wet processes in line.
Impact of the Altium-Ansys Partnership on PCB Design
09/05/2024 | Josh Moore, AltiumThere’s a saying in electronics hardware design: “There are two types of electronics designers: those who have signal integrity problems and those who will.” This adage emphasizes the inevitability of encountering and the need to address signal integrity (SI) and power integrity (PI) issues.
Hidden Cost Drivers in PCB Design
09/05/2024 | Cherie Litson, CID+, Litson1 ConsultingI recently taught a CID+ course, and if you’ve ever taken a CID or CID+ course, you know that we discuss cost adders quite a bit. When I asked the class of 15 design engineers their ideas on the biggest cost adders, the first and strongest response: the project manager. Are you surprised by their answer? After over 40 years in the industry, I wasn’t. If you step back and look at the process of product development, you’ll see that many decisions that affect costs down the line really do take root with the project manager.
Altium, Mouser Team Up to Advance Electronics Education and Careers Worldwide
09/05/2024 | AltiumAltium LLC, a global leader in software and solutions for the electronics industry, and Mouser Electronics, a global authorized distributor of semiconductors and electronic components, are excited to announce a strategic partnership aimed at advancing electronics education and careers worldwide.
Young Professionals Spotlight: Process Engineer Kevin Dial, American Standard Circuits
09/05/2024 | Dan Beaulieu, D.B. Management GroupWhen I heard that my friends at American Standard Circuits had hired a new, fresh-out-of-college process engineer, I was anxious to meet him. Now, you get to read this interview. It’s a rare perspective of a young man new to our industry.