Elementary, Mr. Watson: Rein in Your Design Constraints
Target Condition: Are Autorouters Friend or Foe?
Fresh PCB Concepts: Assembly Challenges with Micro Components and Standard Solder Mask Practices
Thermal Characterization of LEDs: Enabling the Upcoming Lighting Revolution
October 29, 2014 | Dr. John Parry, CEng., Mentor GraphicsEstimated reading time: 1 minute
According to a June 2012 report from the Climate Group, many commercially available, outdoor light-emitting diode (LED) products offer high-quality light, durability, and significant electricity savings in the range of 50 to 70%. More European cities are adopting LED streetlights because LEDs can save energy costs, while exceeding local lighting standards. They last 50,000 to 100,000 hours, change little in color, and have a failure rate of around 1%, compared, for example, to up to 10% for ceramic metal halide fixtures over a similar time period. LED streetlights are a gateway technology--when LED designers solve the current problems of reducing cost and thermal challenges, they’ll be paving the way for wider adoption and the energy-saving potential of LEDs.
Thermal management is one of the more complex areas of LED system design. And until a few years ago, the methods and technology to scientifically characterize the thermal behavior of the component, as well as its systems and subsystems, were not available. Instead, most engineers calculate their thermal needs from data sheets published by component manufacturers. Understandably, having data available to engineers on the specific thermal mechanics of LED-based devices within the system in which they are being used could be a huge step forward for future lighting designs.
This article describes a method that combines hardware measurement (a thermal transient tester), and computational fluid dynamics (CFD) software to provide high measurement throughput, which enables systems integrators to verify a vendor’s thermal resistance data during design and to test incoming commercial off-the-shelf parts before they are introduced into production. This data can be used during the design and product development phase to accurately capture the thermal response of an LED lighting system.
Read the full article here.
Editor's Note: This article originally appeared in the October 2014 issue of The PCB Design Magazine.
Share on:
Suggested Items
Digital Twin Concept in Copper Electroplating Process Performance
07/11/2025 | Aga Franczak, Robrecht Belis, Elsyca N.V.PCB manufacturing involves transforming a design into a physical board while meeting specific requirements. Understanding these design specifications is crucial, as they directly impact the PCB's fabrication process, performance, and yield rate. One key design specification is copper thieving—the addition of “dummy” pads across the surface that are plated along with the features designed on the outer layers. The purpose of the process is to provide a uniform distribution of copper across the outer layers to make the plating current density and plating in the holes more uniform.
Trump Copper Tariffs Spark Concern
07/10/2025 | I-Connect007 Editorial TeamPresident Donald Trump stated on July 8 that he plans to impose a 50% tariff on copper imports, sparking concern in a global industry whose output is critical to electric vehicles, military hardware, semiconductors, and a wide range of consumer goods. According to Yahoo Finance, copper futures climbed over 2% following tariff confirmation.
Flexible Printed Circuit Board Market to Reach US$40.447 Billion by 2030
07/10/2025 | Globe NewswireThe flexible printed circuit board market will grow at a CAGR of 8.28% to be valued at US$40.447 billion in 2030 from US$27.17 billion in 2025.
TTM Technologies Prepares For the Future with the Acquisition of a Facility in Wisconsin and Land in Penang
07/10/2025 | Globe NewswireTTM Technologies, Inc., a leading global manufacturer of technology solutions including mission systems, radio frequency (RF) components and RF microwave/microelectronic assemblies, quick-turn and technologically advanced printed circuit boards (PCB), announced the acquisition of a 750,000-square-foot facility in Eau Claire, Wisconsin, as well as land rights for an additional future manufacturing site in Penang, Malaysia.
Schweizer Electronic: Annual General Meeting Approves All Proposed Resolutions with a Large Majority
07/10/2025 | Schweizer Electronic AGThe Annual General Meeting of Schweizer Electronic AG took place on June 27, 2025, at the company's headquarters in Schramberg.