-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueSilicon to Systems: From Soup to Nuts
This month, we asked our expert contributors to weigh in on silicon to systems—what it means to PCB designers and design engineers, EDA companies, and the rest of the PCB supply chain... from soup to nuts.
Cost Drivers
In this month’s issue of Design007 Magazine, our expert contributors explain the impact of cost drivers on PCB designs and the need to consider a design budget. They discuss the myriad design cycle cost adders—hidden and not so hidden—and ways to add value.
Mechatronics
Our expert contributors discuss the advent of mechatronics in PCB design, the challenges and opportunities this creates for circuit board designers, and the benefits—to the employee and the company—of becoming a mechatronics engineer.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Avoid Overbuilding your RF Printed Circuit Board
July 9, 2015 | Barry Matties, I-Connect007Estimated reading time: 11 minutes
![](https://iconnect007.com/application/files/5616/3116/7912/James_Hofer.jpg)
Today, many companies are overbuilding and “overmaterializing” their RF printed circuit boards. In this interview, James Hofer of Accurate Circuit Engineering (ACE) shares some strategies to avoid doing both, which will help lower the total cost of your PCB and improve the overall product quality. Hofer also discusses some of the challenges in the laminate supply chain.
Barry Matties: Why don't you start by talking about Accurate Circuit Engineering; what do you do and what is your specialty?
James Hofer: Accurate Circuit Engineering is a high-tech prototype facility. We specialize in low volume, high mix. Our specialty is RF and signal integrity products. We do a lot of good cavities, and we handle all specialty materials; we especially use a lot of Rogers, Taconic, and Arlon, which is now also Rogers. We stock R4000 series, because 4000 series is an advanced dielectric for signal integrity. We probably run somewhere between 15 and 30 jobs a week on R4000, which we stock because Rogers just recently was quoted as, "We're very proud to say our lead-time on the 4000 series is now only 35 days." That's more than a month.
We specialize in quick-turn. I can run 16-layer, high-frequency jobs with impedance on multiple layers in 24 hours. We can also go up to 20 days. We do everything from the AT test boards to gigantic antennas. Everybody who has a wave-guide analyzer or an amplifier is using boards for those, and our boards are just the kind of things to go in there.
Matties: Yes, RF is a booming area right now.
Hofer: RF satellite is back up and on top of everybody's minds right now, with all the advanced unmanned vehicles that everybody from civilian to military is using. All of that is RF. We're going faster and faster, higher and higher. All our smartphones are using RF-type and wireless technology. All of that requires test equipment, design equipment, prove-out equipment, and every one of those has a circuit board.
Matties: Your manufacturing focus is RF. How long have you had that focus?
Hofer: I brought that focus on board with Accurate about 12 years ago. I've been with Accurate 15 years now, and when I started we were just doing rigid boards, whatever came our way, and I wanted Accurate to move forward and have a specialty. When somebody says, “Who does RF boards? Oh, Accurate does RF boards,” we are right there. That has really worked out for us, because not only are we seeing a lot of activity in that area, but we were also very good at it. It has really propelled us to the next level.
Matties: We've done a few surveys recently—you may have seen—about supply chain and also the war on failure. In the RF arena, failure is just not even an option when you're dealing with military satellites, commercial aircraft, that sort of thing. How do you battle failure in your process?
Hofer: We start from the minute we get the customer design. We run it through DFM and DRC checks. We verify their calculations. We take a look at how their structure is and how their stack-up is and how they've laid everything out, to make sure that it's going to be robust enough in the finished product to withstand multiple heat cycles, vibration, etc.
Then during our own manufacturing process, because we're also MIL-certified and AS9100 certified, we have process checks and process documentation to ensure that when we're manufacturing the board, it's seeing only processes that have been vetted and are monitored in performance, tracked, and managed. Once the finished product is done, we put it through construction integrity testing, full electrical testing, and then full dimensional and measurement testing before we ship it out to the customer.
Matties: Interestingly, I've looked at this in the supply chain from fabricator to assembler, and it seems to me that no matter how stable your processes are, you could be using best practices and all that but inspections are the only line of defense.
Hofer: Nothing is 100%. Even computers are 99.9999%, and that's not a hundred. Inspection is really the key to prevent escapes, because you're right, in manufacturing, in life, mistakes are going to happen and people are going to make mistakes and mistakes make people. It's how you move forward from them that's important. The inspection steps—which is why we have so many inspection steps along the way of manufacturing and at final—are the only way you keep it from getting out to assembly and then getting out into a product. Even that, unfortunately, is not at 100%. Sometimes things escape. We see it on the news all the time.
Matties: Absolutely. Airbags, ignition switches, falling satellites, or whatever it happens to be.
Hofer: That's correct.
Matties: It's really interesting, and you mentioned materials. The other part we looked at was supply chain and how difficult it is to get materials. What sort of demands or impacts has that had on your business?
Page 1 of 3
Suggested Items
Foxhole Group Boosts Life Science Capabilities with Accutron Partnership
09/03/2024 | Foxhole GroupFoxhole Group, a private investment firm focused on the industrial sector, announced today that it has added significant depth of expertise in life science and aerospace and defense capabilities to its Foxtronics EMS platform by partnering with the Faldu family to add Accutron to the company’s portfolio of EMS brands.
Marshall, Tech Mahindra to Explore Aerospace and Defense Collaboration
09/02/2024 | MarshallMarshall and Tech Mahindra, a leading global provider of technology consulting and digital solutions to enterprises across industries, have signed a Memorandum of Understanding (MoU) to identify and develop opportunities to work together across the aerospace and defense domains.
A Less Expensive Defense and Aerospace PCB Fab Startup
08/20/2024 | Alex Stepinski, Stepinski GroupEditor’s note: Investing in a new printed circuit board fabrication startup is not for the faint of heart or the light of wallet. Standing up a new “high-tech” PCB fab facility capable of becoming qualified for aerospace and defense work typically takes a minimum investment of $50 million. However, Alex Stepinski says entering the defense and aerospace markets with a new PCB fabrication start-up facility far under this prohibitive cost benchmark is possible when good partnerships, innovation, and sound engineering design enter from the beginning. In this article, Alex Stepinski outlines just how this can be achieved.
USPACE and EgSA to Form Aerospace Joint Venture in Egypt
08/16/2024 | PRNewswireUSPACE Technology Group Limited is pleased to announce that the Group has signed the strategic partnership agreement with the Egyptian Space Agency (EgSA), in relation to satellite manufacturing and testing, satellite launch, education and training, greatly expanding its business presence in the fast-growing African space market.
UHDI Fundamentals: UHDI Applications for Aerospace
08/13/2024 | Anaya Vardya, American Standard CircuitsUltra high density interconnect (UHDI) technology refers to advanced manufacturing processes used to create extremely compact and highly efficient electronic circuits at the sub-1-mil line and space level. In aerospace applications, UHDI is crucial due to the stringent requirements for weight, reliability, and performance in a challenging environment.