-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Dana Korf: What Fabricators Expect From Designers
June 18, 2020 | I-Connect007 Editorial TeamEstimated reading time: 2 minutes
Andy Shaughnessy and Barry Matties spoke with Dana Korf, former chief PCB technologist for Huawei and currently principal consultant of Korf Consultancy, about the breakdown in communication between manufacturers and designers. Dana discusses exactly what a fabricator expects from a PCB designer, why these expectations are often not met, and the need for designers to make mistakes so that they can learn from them.
Andy Shaughnessy: Dana, we’re going to talk about expectations and the problems with unmet expectations. Can you give everybody a quick rundown of your background?
Dana Korf: I started out post-Vietnam War in the mini-computer industry where we were trying to displace mainframe computers; it was said that you couldn’t do it, but at the end of a few years, our machine came out, and we could beat them in some benchmarks. Then, PCs came out and displaced that industry. At that time, I was working my first PCB in the fab shop, which was a six-layer board and hand layout with tape with Mylar paper two times the size. Over the years, I worked in fabrication on design for a telecommunications company. I co-founded Interconnect Technology Inc. (ITI) in the early ‘80s with some people from Tektronix, where we had a service bureau set up doing the laser blind via drilling PCB layout, fabrication and surface-mount assembly. Unfortunately, the company didn’t make it, but I made a lot of friends in various groups that scattered out around the industry, and some of them are still around.
After that, I went into telecom design and worked on one of the first fiber-to-the-home distribution systems, and then I went back to the board fabrication industry, where I’ve been there pretty much the last 25+ years. I’ve been involved in high-end circuit board manufacturing, run R&D, and was involved with buried capacitance technology when it first came out. It was a radical idea that enhanced the existing decoupling capacitors with higher frequency plane-to-plane capacitance, which was critical for signal integrity and power distribution. We marketed it for many years then it finally took off. That was with Zycon, then we got bought by HADCO and subsequently by Sanmina, so we had a lot of board shops around the world. I was responsible for the front-end engineering for all the shops globally, where the key challenge was to be able to transfer designs from North America to Europe and Asia; that was difficult because the materials and plant capabilities were not always the same.
To read this entire interview, which appeared in the May 2020 issue of Design007 Magazine, click here.
Suggested Items
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
05/03/2024 | Nolan Johnson, I-Connect007This week’s most important news is strategic—and telling. When one puts together the IPC industry reports, we simply have to include the recent conversation with Shawn DuBravac and Tom Kastner. On the design side, check out the latest “On The Line With…” podcast featuring Brad Griffin from Cadence Design Systems, discussing SI and PI in the realm of intelligent system design.
IMI Welcomes New CEO
05/03/2024 | IMIIntegrated Micro-Electronics, Inc. (IMI),The IMI Board of Directors announced, in a disclosure dated April 25, 2024, the appointment of Louis Sylvester Hughes, Chief Executive Officer (CEO).
Gstar Announced the Strategic Move: Groundbreaking of Silicon Wafer Factory Construction in Indonesia
05/03/2024 | PRNewswireRecently, Gstar held a groundbreaking ceremony for its silicon rod and silicon wafer factory, marking the beginning of the rapid construction phase.
ZESTRON Academy Launches 2024 Advanced Packaging & Power Electronics Webinar Series
05/01/2024 | ZESTRONZESTRON, the leading global provider of high-precision cleaning products, services, and training solutions in the electronics manufacturing and semiconductor industries, proudly announces the launch of its highly anticipated webinar series on Advanced Packaging & Power Electronics, a webinar series on the latest innovations, cleaning, and corrosion challenges.
On the Line With… Talks With Cadence Expert on SI/PI for PCB Designers
05/02/2024 | I-Connect007In “PCB 3.0: A New Design Methodology—SI/PI for PCB Designers,” subject matter expert Brad Griffin, Cadence Design Systems, discusses how an intelligent system design methodology can move some signal and power integrity decision-making into the physical design space, offering real-time feedback.