Designers Notebook: Impact of Advanced Semiconductor Packaging on PCB Stackup
Fresh PCB Concepts: PCB Stackup Strategies—Minimizing Crosstalk and EMI for Signal Integrity
Connect the Dots: Designing for Reality—Solder Mask and Legend
Designing Additive and Semi-Additive PCBs
April 26, 2022 | Cherie Litson, CID+, Litson1 ConsultingEstimated reading time: 1 minute
With components getting smaller and electronic devices becoming more compact, we are reaching the physical limits of the typical etched fabrication processes. To address these limits, new additive and semi-additive processes are being developed to fit into the current fabricators’ production lines without too much disruption or extra cost.
That leaves the design engineer with a few questions: Will additive and semi-additive processes really reduce layer count and sizes? Are there signal integrity and impedance advantages and disadvantages? When does it makes sense to switch to additive or semi-additive? Are my DFMs going to be any different?
Answers to these questions and many more are still being developed. However, I’ve found a few answers that I’m happy to share with you.
First, let’s look at liquid metal ink. LMI is ultra-thin and ultra-dense, conforms to any 3D surface, works with different pure metals and their alloys (copper, gold, silver, palladium, platinum, etc.), and is non-aqueous, which enables low-cost manufacturing.
Here are some fundamentals for these very small features. Figure 1 depicts some examples of the additive processes used to create fine copper traces on a printed circuit board. One of the first things you’ll notice are the shapes of the traces: They are not trapezoidal.
To read this entire article, which appeared in the April 2022 issue of Design007 Magazine, click here.
Share on:
Suggested Items
Designers Notebook: Impact of Advanced Semiconductor Packaging on PCB Stackup
01/07/2025 | Vern Solberg -- Column: Designer's NotebookTo accommodate new generations of high I/O semiconductor packaging, printed circuit board fabrication technology has had to undergo significant changes in both the process methods and the criteria for base material selection and construction sequence (stackup). Many of the new high-function multi-core semiconductor package families require more terminals than their predecessors, requiring a significantly narrower terminal pitch. Interconnecting these very fine-pitch, high I/O semiconductors to the PCB is made possible by an intermediate element referred to as an interposer.
BOOK EXCERPT: The Printed Circuit Designer’s Guide to... High Performance Materials, Chapter 4
01/02/2025 | I-Connect007In Chapter 4, Michael Gay discusses the two main types of copper foil used for PCB boards today: electrodeposited (ED) foil and rolled annealed (RA) foil. He also explains the pros and cons of each, and provides an update of the latest innovations in copper foil technology.
Connect the Dots: Designing for Reality—Solder Mask and Legend
01/02/2025 | Matt Stevenson -- Column: Connect the DotsIn the previous episode of I-Connect007’s On the Line with… podcast, we discussed the strip, etch, and strip process. At this point, we have a functioning board, but we still need to protect the PCB from environmental effects and document the circuit components. This brings us to the solder mask and legend phase of production.
Global PCB Connections: Following DFM Rules Leads to Better Boards
12/18/2024 | Jerome Larez -- Column: Global PCB ConnectionsAs a PCB field applications engineer, ensuring smooth communication between PCB designers and fabricators is one of my frequent challenges. A critical part of that dialogue is design for manufacturing (DFM). Many designers, even experienced ones, often misunderstand or overlook important DFM considerations. They may confuse design rules with manufacturing minimums, leading to technically feasible designs that are difficult or costly to produce. In this column, I will clarify some common DFM guidelines and help designers understand the difference between “design rules” and “minimums” while sharing best practices that will simplify the production process and ensure the highest quality PCB.
Sayonara to the Last Standing Copper Foil Plant in North America
12/17/2024 | Marcy LaRont, I-Connect007In July 2021, PCB007 Magazine published an interview with Michael Coll and Chris Stevens of Nippon Denkai about the new acquisition by Nippon Denkai of the last-standing ED foil manufacturer in North America. The plant in Augusta, Georgia, was formerly owned by Oak Mitsui, Inc. and had been purchased by Nippon Denkai the previous March, after which significant investment was made with the expectation of providing more jobs.