Connect the Dots: Sequential Lamination in HDI PCB Manufacturing
Target Condition: The 5 Ws of PCB Design Constraints
Fresh PCB Concepts: More Than Compliance—A Human-centered Sustainability Approach
Failure Mode: Hole Wall Pullaway
September 16, 2015 | Paul Reid, ConsultantEstimated reading time: 1 minute
Hole wall pullaway (HWPA) is an insidious defect that is not usually a cause of electrical failure. What happens with HWPA is that the copper plating in a plated through-hole (PTH) is pulled away from the dielectric of the drilled hole wall. The hole must not be filled with any sort of a hole fill in order to see HWPA.
There are two distinct types of HWPA: stress-relieving and stress-inducing. In stress-relieving HWPA, the condition appears to distress the PTH, allowing it to survive hundreds or thousands of thermal cycles without failure. In stress-inducing HWPA, the stress appears to greatly increase, causing the PTH to fail in just a few thermal cycles. What we consider a failure is an increase greater than 10% in the overall resistance in the circuit. A crack that partially bridges the copper at the internal interface is enough to cause a failure.
This column is based on my experience in test reliability of interconnect stress test (IST) coupons. I am addressing HWPA that features moderate to severe outgassing. There may be HWPA due to thermal stressing of the board without any significant outgassing, but this type of HWPA is subtle, and it presents as a dark line between the plating and the dielectric of the hole wall. This type of HWPA is rarely detected.
Stress-Relieving HWPA
Stress-relieving is the most common type of HWPA. It appears that the adhesion of copper plating to the dielectric is reduced most likely due to problems with the application of electroless copper plating adhering to the dielectric of the hole wall. At the same time, the adhesion is strong at the copper’s internal interconnection. In fact, experience suggests that the adhesion of the electroless copper is stronger than the copper plating. This process frequently produces strong interconnections to copper inner layers. This condition may result in a hole wall that looks like a stack of forward or backward “Ds” running the length of the hole where the top and the bottom of the “Ds” is at an internal interconnect.
To read this entire article, which appeared in the August 2015 issue of The PCB Design Magazine, click here.
Share on:
Testimonial
"The I-Connect007 team is outstanding—kind, responsive, and a true marketing partner. Their design team created fresh, eye-catching ads, and their editorial support polished our content to let our brand shine. Thank you all! "
Sweeney Ng - CEE PCBSuggested Items
Statement from the Global Electronics Association on the July 2025 Tariff on Copper Foil and Electronics-Grade Copper Inputs
07/31/2025 | Global Electronics AssociationWe are disappointed by today’s decision to impose a 50% tariff on imported copper foil and other essential materials critical to electronics manufacturing in the United States.
Considering the Future of Impending Copper Tariffs
07/30/2025 | I-Connect007 Editorial TeamThe Global Electronics Association is alerting industry members that a potential 50% tariff on copper could hit U.S. electronics manufacturers where it hurts.
Connect the Dots: Sequential Lamination in HDI PCB Manufacturing
07/31/2025 | Matt Stevenson -- Column: Connect the DotsAs HDI technology becomes mainstream in high-speed and miniaturized electronics, understanding the PCB manufacturing process can help PCB design engineers create successful, cost-effective designs using advanced technologies. Designs that incorporate blind and buried vias, boards with space constraints, sensitive signal integrity requirements, or internal heat dissipation concerns are often candidates for HDI technology and usually require sequential lamination to satisfy the requirements.
OKI Launches Rigid-Flex PCBs with Embedded Copper Coins Featuring Improved Heat Dissipation for Space Equipment Applications
07/29/2025 | BUSINESS WIREOKI Circuit Technology, the OKI Group’s printed circuit board (PCB) business company, has developed rigid-flex PCBs with embedded copper coins that offer improved heat dissipation for use in rockets and satellite-mounted equipment operating in vacuum environments.
Designers Notebook: Basic PCB Planning Criteria—Establishing Design Constraints
07/22/2025 | Vern Solberg -- Column: Designer's NotebookPrinted circuit board development flows more smoothly when all critical issues are predefined and understood from the start. As a basic planning strategy, the designer must first consider the product performance criteria, then determine the specific industry standards or specifications that the product must meet. Planning also includes a review of all significant issues that may affect the product’s manufacture, performance, reliability, overall quality, and safety.