Beyond Design: High-speed Rules of Thumb
Global PCB Connections: A Technical Overview of Long-flex Printed Circuit Boards
The Shaughnessy Report: A Handy Look at Rules of Thumb
Alpha Takes the Greenfield Route
February 28, 2023 | Nolan Johnson, I-Connect007Estimated reading time: 2 minutes
Alpha Circuit is a PCB fabricator located in Elmhurst, Illinois. Given that the launch of a new PCB fab is a rare occasion these days, we caught up with the senior team—Prashant Patel, president and CEO; Steve Smith, general manager; Steve Ryan, sales and direct support—guiding the buildout of Alpha Circuit’s brand new 44,000 square foot facility. They discuss what goes into equipment selection and line design, and the timing couldn’t have been better. At press time, the new facility was on schedule for test production by the end of January 2023.
Throughout the conversation, the Alpha team shared its methods for designing the facility, the parts of the fabrication process that are critical to get exactly right, and where the surprises were in the process.
Nolan Johnson: Gentlemen, welcome, and congratulations on your new facility. Let’s start with a little background about the company.
Steve Ryan: Alpha Circuit started in 1981, as a single- and double-sided board shop. Zenith was one of our big customers early on. We did a lot of punching and crunching back then and it is what really catapulted the revenue stream for us. When I joined the company in 2009, we were comfortably an eight to 12-layer multilayer and double-sided manufacturer. In 2013, we started doing flex and rigid-flex, increased our multilayers up to 28 layers, and started manufacturing copper-based pedestal-type design work.
Prashant Patel: When I acquired the company in 2020, my vision was to continue Alpha Circuit the way it was, while building a new facility to meet the higher technology demands. We purchased and renovated a 44,000 square foot facility, then ordered the equipment. It takes a long time to source equipment—you get the quotes, have it installed, and then get it running up to speed. That process has taken us over three years.
Steve Smith: I joined the company approximately two months ago. My background is HDI: stacked microvias, staggered microvias, along with high-speed digital materials, low-loss materials. I was hired to put the technology part of it together, getting the proper people and processes in place, so we can handle microelectronics down to 25-micron line and space and down to 3-mil pads.
Johnson: Great, thank you for that. Now, I want to talk today about your recent equipment purchases.
Smith: We have purchased a laser drill, and we have brand-new 200,000 RPM drill machines in place to do high aspect ratio holes. We also have a brand-new plating line with state-of-the-art chemistries to be able to do copper fill and through-hole plating in the same process along with being able to manufacture stacked vias starting with a 2-mil core substrate and stacking up to seven or eight lamination cycles.
To read this entire conversation, which appeared in the February 2023 issue of SMT007 Magazine, click here.
Share on:
Suggested Items
Unlocking Advanced Circuitry Through Liquid Metal Ink
10/31/2024 | I-Connect007 Editorial TeamPCB UHDI technologist John Johnson of American Standard Circuits discusses the evolving landscape of electronics manufacturing and the critical role of innovation, specifically liquid metal ink technology, as an alternate process to traditional metallization in PCB fabrication to achieve ever finer features and tighter tolerances. The discussion highlights the benefits of reliability, efficiency, and yields as a tradeoff to any increased cost to run the process. As this technology becomes better understood and accepted, even sought out by customers and designers, John says there is a move toward mainstream incorporation.
Fresh PCB Concepts: The Critical Nature of Copper Thickness on PCBs
10/31/2024 | Team NCAB -- Column: Fresh PCB ConceptsPCBs are the backbone of modern electronics and the copper layers within these boards serve as the primary pathways for electrical signals. When designing and manufacturing PCBs, copper thickness is one of the most critical factors and significantly affects the board’s performance and durability. The IPC-6012F specification, the industry standard for the performance and qualification of rigid PCBs, sets clear guidelines on copper thickness to ensure reliability in different environments and applications.
Book Excerpt: The Printed Circuit Designer’s Guide to... DFM Essentials, Ch. 1
10/25/2024 | I-Connect007The guidelines offered in this book are based on both ASC recommendations and IPC standards with the understanding that some may require adjustment based on the material set, fabricator processes, and other design constraints. This chapter details high-frequency materials, copper foil types, metal core PCBs, and the benefits of embedded capacitance and resistor materials in multilayer PCBs.
The Cost-Benefit Analysis of Direct Metallization
10/21/2024 | Carmichael Gugliotti, MacDermid AlphaCarmichael Gugliotti of MacDermid Alpha discusses the innovative realm of direct metallization technology, its numerous applications, and significant advantages over traditional processes. Carmichael offers an in-depth look at how direct metallization, through developments such as Blackhole and Shadow, is revolutionizing PCB manufacturing by enhancing efficiency, sustainability, and cost-effectiveness. From its origins in the 1980s to its application in cutting-edge, high-density interconnects and its pivotal role in sustainability, this discussion sheds light on how direct metallization shapes the future of PCB manufacturing across various industries, including automotive, consumer electronics, and beyond.
Connect the Dots: Designing for Reality—Pattern Plating
10/16/2024 | Matt Stevenson -- Column: Connect the DotsIn the previous episode of I-Connect007’s On the Line with… podcast, we painted the picture of the outer layer imaging process. Now we are ready for pattern plating, where fabrication can get tricky. The board is now ready to receive the copper traces, pads, and other elements specified in the original CAD design. This article will lay out the pattern plating process and discuss constraints in the chemistries that must be properly managed to meet the customer's exacting manufacturing tolerances.