Connect the Dots: Designing for Reality—Pattern Plating
Elementary, Mr. Watson: The Gooey Centers of Hybrid PCB Designs
The Shaughnessy Report: Are You Partial to Partial HDI?
Stop Over-specifying Your Materials
May 25, 2023 | I-Connect007 Editorial TeamEstimated reading time: 3 minutes
Columnist Kelly Dack has had a pretty wide range of experiences. As a PCB designer, he has sat behind the desk at an NPI company, an OEM, a fabricator, and now an EMS provider. We asked him to share a few thoughts on the materials selection process and how it could be improved.
Kelly also explains how overly zealous PCB designers make things too complicated by over-specifying their materials, which leads to confusion once the board goes to volume production overseas. Are you over-constraining your material choices?
Andy Shaughnessy: Kelly, what is your process for material selection? Walk us through it.
Kelly Dack: Sure. I actually wrote a guideline for our customers that explains the material selection process. As mentioned, over-specification in the EMS realm is rampant and problematic from the standpoint of scaling products to volume overseas. This guide has a section on laminated materials that includes a simple, tried-and-true material specification. It says, “Materials: laminated glass epoxy resin type FR-4 series or equivalent per IPC-4101 with a Tg of greater than or equal to xxx.” This is a number that we can modify. We say, for instance, 170°C, and a Td (time to delamination) temperature of greater than 3XX°C. Those are all movable numbers that designers can edit.
That’s how we specify our laminate materials for printed circuit boards, unless the performance criteria dictates that it needs to go further and get more specific—for example, high-performance signal integrity constraints, impedance control, or exotic materials. But otherwise, FR-4 laminates cover 85–95% of our customers’ design requirements.
Shaughnessy: Where do designers typically go to find this information? What documents or guidelines should they use?
Dack: Many designers use their company’s documentation template or go to their elders and learn through knowledge that has been passed down. I just went through a bunch of our customers’ designs and fabrication drawings, and I found plenty of examples of customer material specification. Many of them call out a specific IPC-4101 slash number, and it’s usually the same slash number each time. It’s either 4101/26 or /21.
Shaughnessy: IPC has said that slash sheets were not ever meant for designers to use; they’re mainly a way for PCB supplier purchasing and marketing departments to communicate with buyers.
Dack: I’m glad to hear that confirmation as it was my understanding as well. This all came from the MIL-S-13949 spec back in the mil-spec days, most of which has been replaced by IPC standards. But we are seeing some of our customers’ designs specifying laminates by using slash numbers and I get the feeling it’s just because of tribal knowledge. If you look at most of the designs, they appear to be basic, not really requiring a specific material. The board would work fine with a generic glass-epoxy laminate because it has no impedance control or performance criteria. We just print and etch some copper onto it, create a circuit, and it moves electrons.
It’s usually only when we get into the super high-speed design in the gigahertz range where we have to start thinking about loss tangents and permittivities. Here’s the challenge: How much do you constrain? If you’re building your PCB design down at the local prototype shop, which will build a board any way you want, everybody seems fat and happy. But when you want to build 1 million boards, you must introduce a low-cost constraint because you can’t pay $1,000 a board and make a profit. You scale to volume to get cost savings. To realize maximum cost savings, this has always been done offshore. But designers must realize that offshore suppliers don’t have access to all the materials and capabilities that U.S. prototype companies have. Over-specification of laminate materials by composition, performance characteristics, or a trademarked source creates a terrible, but avoidable ordering situation, putting quotes on hold every single day. The simple fact is that it causes our offshore PCB suppliers to request and obtain approval for material substitutions before they can proceed.
To read this entire conversation, which appeared in the May 2023 issue of Design007 Magazine, click here.
Share on:
Suggested Items
The Cost-Benefit Analysis of Direct Metallization
10/21/2024 | Carmichael Gugliotti, MacDermid AlphaCarmichael Gugliotti of MacDermid Alpha discusses the innovative realm of direct metallization technology, its numerous applications, and significant advantages over traditional processes. Carmichael offers an in-depth look at how direct metallization, through developments such as Blackhole and Shadow, is revolutionizing PCB manufacturing by enhancing efficiency, sustainability, and cost-effectiveness. From its origins in the 1980s to its application in cutting-edge, high-density interconnects and its pivotal role in sustainability, this discussion sheds light on how direct metallization shapes the future of PCB manufacturing across various industries, including automotive, consumer electronics, and beyond.
Connect the Dots: Designing for Reality—Pattern Plating
10/16/2024 | Matt Stevenson -- Column: Connect the DotsIn the previous episode of I-Connect007’s On the Line with… podcast, we painted the picture of the outer layer imaging process. Now we are ready for pattern plating, where fabrication can get tricky. The board is now ready to receive the copper traces, pads, and other elements specified in the original CAD design. This article will lay out the pattern plating process and discuss constraints in the chemistries that must be properly managed to meet the customer's exacting manufacturing tolerances.
PCB007 Magazine October 2024: Alternate Metallization Processes
10/16/2024 | I-Connect007 Editorial TeamTraditional electroless copper and electroless copper immersion gold have been primary PCB plating methods for decades. But alternative plating metals and processes have been introduced over the past few years as miniaturization and advanced packaging continue to develop taking us into new directions. In this issue of PCB007 Magazine, we examine the impact of alternate metallization methods giving a glimpse into how and when we will arrive at 'destination metallization'.
Partial HDI: A Complete Solution
10/10/2024 | I-Connect007 Editorial TeamWe recently spoke with IPC instructor Kris Moyer about partial HDI, a process that’s recently been growing in popularity. Partial HDI allows designers to escape route out from tight-pitch BGAs on one layer, where a mechanically drilled plated through-hole is not an option, while avoiding the complexity and expense of sequential lamination cycles. As Kris explains, this process doesn’t add much to the cost, and it’s fairly straightforward. But there are some competing signal integrity and fabrication requirements to contend with. We asked Kris to walk us through this process.
Trouble in Your Tank: Interconnect Defect—The Three Degrees of Separation
10/01/2024 | Michael Carano -- Column: Trouble in Your TankIt has been well documented that, with a very expensive and complex printed circuit board, thermal and mechanical excursions often find weaknesses. A lack of robustness and poor process control often leads to the exploitation of those weaknesses. An interconnect defect (ICD) often goes undetected until the printed circuit board reaches the final assembly stage or undergoes multiple thermal cycles, including interconnect stress tests or thermal shock. It is impossible to rework the ICD defect. But unlike voids, if detected in time, the panels can be reprocessed.