Latest Articles

The PCB Norsemen: Industry 4.0, AI and CircuitData

As automation works its way onto the shop floors, it still struggles to replace humans in the supporting roles, such as designers, purchasers, brokers, and back-office staff. Where automation on the shop floor replaces humans in doing repetitive manual tasks, the supporting roles (at least some of them) require intelligence to understand and utilise information.

Nine Dot Connects: Good Design Instruction is a True Value-Add

Nine Dot Connects has certainly blazed an interesting trail. The company started out as an Altium reseller, but in less than a decade, Nine Dot Connects has also become a design service bureau and a provider of PCB design instruction, training, and consulting services. I recently interviewed Paul Taubman, technical services director for Nine Dot Connects. We discussed the company’s expansion from VAR to service bureau and content provider, and the changing landscape of PCB design instruction.

AltiumLive Summit—Munich, Germany, Part 2

Pete Starkey continues with his review of the AltiumLive PCB Design Summit held recently in Munich, Germany. The second day commenced with a new product launch. “Working together is hard” it read on the screen. Statistics indicated that 33% of new products were late getting to market, of which 28% were late due to insufficient collaboration, and up to 50% of potential revenue could be lost through being late to market. Then the screen read “NEXUS makes it easy!”

AltiumLive Summit—Munich, Germany, Part 1

Altium held a very successful AltiumLive PCB Design Summit in San Diego, California at the beginning of October for the benefit of their North American design community, and followed it three weeks later with a counterpart European event in Munich. And what an eye-opener it proved to be—literally hundreds of delegates, a superbly organised and managed programme, billed as a completely immersive two-day interactive design experience on a theme of learning, connecting and getting inspired.

Happy Holden and Charles Pfeil Discuss the Past and Future of PCB Design, Part 1

When it comes to the PCB design community and the challenges facing it, as well as where design has been and where it’s heading, there aren’t many people as qualified to speak on the topic as long-time industry veterans Happy Holden and Charles Pfeil. Joined by I-Connect007’s Barry Matties at the recent AltiumLive 2017 event in San Diego, the three sat down for a discussion about the current state of PCB design, what the future holds, and what it means to be a designer.

Insulectro Teams with Isola to Address Signal Integrity Needs

Insulectro and Isola recently shared a combined booth during PCB West 2017. Insulectro has distributed Isola materials for years, and the companies wanted to focus on Isola’s line-up of high-speed, low-loss material sets. Insulectro’s Chris Hunrath, VP of Technology, and Norm Berry, Director of Laminates and OEM Marketing, sat down with me to discuss the challenges facing signal integrity engineers today, and some of the Isola low-loss, low-Dk materials that can help with their signal integrity requirements. You might find Chris and Norm speaking to a group of PCB designers near you.

SiSoft Preparing for DDR5 Simulation Next Year

DDR5 is expected to double the memory bandwidth and density of DDR4. Andy Shaughnessy recently spoke with SiSoft CTO Walter Katz about his company’s efforts to hit the market with this game-changing technology in 2018.

The History of Predictive Engineering

It all started in 1983, at HP, when I complained to our group's vice president that our W. Edwards Deming and Total Quality Management (TQM) Six Sigma training was being concentrated in PCB manufacturing. We had eliminated final inspection and instead placed quality in the hands of the operators with a final electrical test. The electrical test was governed by what we learned from Deming.

AltiumLive 2017 Munich: Sold Out!

I recently sat down with Ted Pawela, Lawrence Romine, and Judy Warner of Altium to wrap up their sold-out AltiumLive 2017 PCB Design Summit in Munich, Germany. This conference, following on the heels of an AltiumLive event in San Diego, was packed full of PCB designers who attended a series of great keynotes and an excellent technical program. We discussed some of the highlights of the show, including designers’ reactions to a new version of Altium Designer 18 and the brand-new Altium Nexus tool.

GCSI's James Kozich Discusses Industry Hiring Trends

James Kozich of Gilbert Consulting Services has been matching qualified technologists with the right jobs for decades, from the shop floor to C suite positions. During SMTA International, he sat down with Andy Shaughnessy to discuss the recent hiring trends he's seeing in electronics manufacturing.

Sunstone Integrates SnapEDA Libraries into PCB123

Sunstone Circuits and SnapEDA recently announced that SnapEDA’s parts library would be integrated into Sunstone’s PCB123 design tool. During PCB West, I interviewed EDA Product Manager Nolan Johnson of Sunstone Circuits and SnapEDA President Natasha Baker. We discussed their new partnership, the changing parts library landscape, and where the companies see this alliance heading in the future.

Carl Schattke: I Started Designing Boards When I Was 12

Growing up with a father who owned a PCB design bureau, Carl Schattke, CID+, may have been predestined to design circuit boards for a living. In fact, he’s been designing boards for nearly his entire life. Carl gave a keynote speech at the recent AltiumLive event in San Diego, where I caught up with him to discuss a lifetime spent in PCB design, as well as the graying of the PCB design community and what might be done to inspire a youth movement in PCB design.

Meet One of the Industry’s Newest PCB Designers

Molly Knewtson is a recent graduate now working for a pharmaceutical company as a mechanical engineer. She was asked if she would consider learning PCB design and taking on some design projects. She agreed, though she had never considered circuit design as a career path. I sat down with Molly at PCB West to learn how she came to this position and what might be done to inspire more people from her generation to join the industry.

Polar Instruments’ Martyn Gaudion Discusses Tools and Books

Polar Instruments has pretty been busy lately. In the last year, Managing Director Martyn Gaudion has written two books for I-Connect007, and the company has been working to upgrade its tools, especially library functionality. I met with Martyn at PCB West. We discussed Polar’s newest tool updates, Martyn’s new side job as an author of technical books, and the continuing growth of the EDA segment, including among young people.

Dan Beeker’s AltiumLive Keynote: It's All about the Space

Dan Beeker of NXP Semiconductors was a keynote speaker at the recent AltiumLive 2017 event in San Diego. His presentation focused primarily on the design of three-dimensional structures and how it’s all about space. I caught up with Dan, and we discussed his presentation, his background and career, and what kind of advice he would give to young PCB designers.

A Guide to IPC Survey and Report Season

IPC Director of Market Research Sharon Starr found time to discuss the recently conducted and published surveys and research reports and a few others still in the works. These reports are free to survey participants, which is certainly a great incentive for taking the time to complete them. (Hint: That’s a call to action for those of you sitting on the sidelines.)

PCB Signal Integrity Optimization Using X-ray Metrology

It happens again. A new backbone router/switch build or a line card upgrade is approaching completion when something goes wrong. The system won’t operate at the targeted data rate. Deadlines are looming and the root cause of the problem is buried somewhere in a big rack of electronic components.

Altium Designer 18 Introduced at AltiumLive 2017

At the recent AltiumLive 2017 event in San Diego, I sat down for an interview with Dan Fernsebner, Altium’s global head of technical marketing. Dan discussed the upcoming release of Altium Designer 18, as well as the company’s corporate responsibility for giving back to the industry and bringing more young people into EDA. The event featured speakers such as Happy Holden, Dan Beeker, Charles Pfeil, and Tara Dunn, as well as a robot team competition.

AltiumLive 2017 Attracts Hundreds of Designers

Altium conducted its first-ever users conference, AltiumLive 2017: Annual PCB Design Summit, at the Hilton Resort and Spa on beautiful Mission Bay in San Diego. This conference included a lineup of notable speakers, including four keynote speeches over the two-day event. This conference drew hundreds of PCB designers, many of whom attended breakout sessions designed in accordance with the show’s motto, “Learn – Connect – Get Inspired.”

Full Coverage of AltiumLive 2017

Altium recently conducted its first-ever users conference, AltiumLive 2017: Annual PCB Design Summit, at the Hilton Resort and Spa in San Diego. Speakers included Dan Beeker of NXP Semiconductors, Max Seeley of 3M Corporate R&D, Tara Dunn of OMNI PCB, Susy Webb of Fairfield Nodal, Charles Pfeil of Altium, and our own Happy Holden. This conference drew hundreds of PCB designers, and included a robot design challenge and battle. If you couldn’t make it, don’t worry. We shot a variety of video and still photos.

Predictive Engineering: Happy Holden Discusses True DFM

Happy Holden has been involved in DFM for over 45 years, since he first started working at HP and optimized their PCB design and manufacturing processes. Naturally, for this issue, Barry Matties and Andy Shaughnessy made it a priority to get Happy’s thoughts on DFM, and what true DFM entails.

It’s Not Your Father’s DFM Anymore

What does DFM look like today? Well, for one, it’s become more than DFM. We now expect our software tools to serve us more completely to take new designs to market. DFM has evolved to become an integral part of new product introductions (NPI). Today’s NPI software spans design and manufacturing to accelerate the optimization of a PCB for manufacturing. It looks at the entire design-to-manufacturing release process and deliverables, then streamlines them.

The State-of-the-Art in PCB Pre-production Engineering

If there’s one benefit of old age, it’s being able to remember the introduction to our industry of technologies that may be taken for granted by the present generation, but were revolutionary at the time. I can recall the history of Ucamco as far back as the late 1980s when, as one of the very early adopters of the DISC laser plotter and its associated electronic PCB front-end tooling system, our company gained entry to a spectacular new world of pre-production engineering capability.

RTW SMTAI: Judy Warner Discusses AltiumLive: 2017 and Her New Role

At SMTA International in Rosemont, Illinois, Judy Warner of Altium discusses her new role as director of community engagement. She also details AltiumLive: 2017, which takes place October 3-4 at the Hilton San Diego Resort and Spa. AltiumLive features Happy Holden and Charles Pfeil, as well as a robot design challenge and battle.

Sensible Design: Thermal Management—The Heat is On

Thermal management materials are designed to prolong equipment life and reduce incidences of failure. They also maintain equipment performance parameters and reduce energy consumption by reducing operating temperatures, and minimising the risk of damage to surrounding components. Indirectly, they maintain brand reputation, as the reliability of the equipment will be very dependent upon the effectiveness of the thermal management technique used.

Fault-Finding: It’s All About Prevention, not Blame

There are thousands of things that can go wrong during the design and manufacture of a PCB assembly. One might say that it is an absolute miracle when a PCB goes through all of its phases—design, fabrication and assembly—and operates successfully. But there are some management and customer cultures who naively attempt to resolve problems by seeking out the culprits and shouting “Off with their heads!”

Whose Fault is That Bad Board?

Years ago, I held a position in an EMS company where projects were analysed before manufacturing. We found that even some of the best and most innovative circuits could not be manufactured. Why? Because the PCB designer, an electronic engineer, was not acquainted with the fabrication process. He had no idea about technological requirements necessary for electronic production. I know another designer who learned, finally, the importance of the thermal relief pad for heat restriction during reflow for a good soldering. His response? “Oh, was that what they were for? And to think I worked so much to remove them!”

Enough Blame to Go Around

The idea for this article began a few months ago when The PCB Design Magazine conducted a reader survey regarding the topic “Whose Fault is that Bad Board?” After some thought, I submitted my answers. After all, I must have some kind of input after over 25 years of PCB design. But still, whose fault is that bad board? OK, I know what you’re thinking: Don’t go there. We designers make mistakes too.

The International Paris Air Show with ASC’s Anaya Vardya

The International Paris Air show is the crème de la crème of the world’s trade shows. This is the big one, where all the aircraft, airline and defense aerospace companies meet to introduce new products, discuss the future of aviation, and make deals. This year I decided to talk to my friend Anaya Vardya, ASC’s president and CEO, about the show, why he goes and what it’s like.

Resins: Cutting Through the Technical Jargon

This month, I’m going to cut through some of the more heavy-going tech-speak, taking a few of my customers’ more frequently asked questions about resins to try to help you refine your selection process. There’s a lot of ground to cover, but for the purposes of this column, let’s concentrate on the PCB’s operating environment, caring for the components that are to be encapsulated, and the special needs of applications like LED lighting and RF systems.

Stephen V. Chavez Talks Mil/Aero PCB Design

Stephen V. Chavez, CID+, is the lead PCB designer for the Electronic Systems Center division of UTC Aerospace Systems (UTAS), a military contractor that builds all manner of cutting-edge tools for the American warfigher. He’s been designing military and aerospace PCBs for decades, and he’s a veteran of the United States Marine Corps. I caught up with Steph and asked for his thoughts on designing PCBs for the military and aerospace markets.

Orange Co. Designers Council Meeting Focuses on Embedded Passives

On July 19, the Orange County Chapter of the IPC Designer’s Council hosted a lunch-and-learn meeting in Tustin to discuss the benefits of embedded passives. Approximately 40 people were in attendance, which was lighter turnout than usual, most likely because of summer vacations. But the crowd was an enthusiastic one, as usual. The first speaker was Bruce Mahler of Ohmega Technologies, followed by Jin Hyun-Hwang of Dupont.

IMPACT Interview: Fern Abrams, IPC

At the recent IMPACT Washington D.C. 2017 event, I-Connect007's Patty Goldman speaks with IPC's Fern Abrams to get the inside story on the meeting with EPA.

Using Vibration and Acceleration Analysis to Improve Reliability

Deriving the physical constraints and fatigue issues for a design prior to manufacturing is essential to reducing board failure and thereby improving product quality. In harsh environments, fatigue can be responsible for up to 20% of failures. Customers have come to expect reliability across the industry spectrum no matter where actual production occurs. Reliable products have less risk of failure, less field returns and less warranty claims, all of which contribute to higher profitability. It is a given that every product is expected to fail at some point, however premature failures can be mitigated through proper design with attention to potential issues due to vibration and acceleration.

Trilogy Circuits: Mil/Aero Demands Technological, Regulatory Expertise

In the 16 years since its founding, Trilogy Circuits has become one of the go-to companies for mil/aero PCB design and manufacturing. I spoke with Charlie Capers, president and founder of the Richardson, Texas firm, about how he keeps ahead of the game. As he explains, succeeding with mil/aero PCB work requires not only mastery of the technological side, but of the regulations and certifications as well.

PCB Designers Notebook: Embedding Components, Part 2

Technology and processes for embedding capacitor and inductor elements rely on several unique methodologies. Regarding providing capacitor functions, IPC-4821 defines two methodologies for forming capacitor elements within the PCB structure: laminate-based (copper-dielectric-copper) or planar process and non-laminate process using deposited dielectric materials.

Performance Evaluation of Thin-Film Embedded Resistors

Thin-film microstrip circuits have been widely applied in microwave communications, electronic countermeasures (ECM), and aerospace applications, etc. When manufacturing thin-film ICs, it is very important to apply deposited thin-film resistor material to fabricate high-accuracy and highly stable thin-film embedded resistors. Thin-film ICs call for thin-film resistors that meet stringent requirements.

Review of the 2017 IPC Reliability Forum

IPC continues to lead our industry by example with their inaugural Reliability Forum, held in Chicago in April. The event was focused on manufacturing high-performance products and featured industry royalty from both a speaker and audience standpoint.

Embedded Technology: A Useful Tool in Freedom CAD’s Toolbox

Freedom CAD has been designing and fabricating boards with embedded technology for years, and doing some pretty innovative work along the way. I asked Scott McCurdy, Freedom CAD’s director of sales and marketing, to share some details about their embedded processes, as well as the challenges and opportunities that embedded technology offers.

New Challenges Facing Mil/Aero Segment

For this month's issue, we invited a sampling of professionals whose experience centers on the electronics industry in the military and aerospace world, including experts from design, PCB manufacturing, and the assembly arena to sit down with us for a frank discussion. Our discussion centered on the challenges associated with military work, including the new regulatory requirements for cybersecurity, dealing with leaded vs. lead-free components, and the differences and similarities with the commercial world.

A Deep Look Into Embedded Technology

In preparation for this month’s magazine, we set up a conference call with the goal of uncovering the challenges and opportunities related to embedded technology. Invited were a handful of the industry’s heavy hitters in the embedded world: Retired technologist and I-Connect007 Contributing Editor Happy Holden, and Ohmega’s Technical Director Daniel Brandler and Design & Test Engineer Manuel Herrera.

Launching a New PCB Design Curriculum in Serbia

Let me share with you an experience that I remember from my college days. When I was a student, I had a professor who was too proud of the fact that she was an academic. “You don’t need to know how to manually solder electrical parts or how to design printed circuit boards,” she lectured. “It is important that you understand the formula for charge carrier currents in a p-n junction.” I started working as an R&D engineer for a Swiss company that developed and manufactured instruments for measuring magnetic fields and electrical currents. And nobody ever asked me about charge carriers in p-n junctions.

Technology Enabler Highlights Benefits of Having Design Services for an EMS Firm

At the 14th Philippine Semiconductor and Electronics Convention and Exhibition (PSECE) held last week in Manila, Robin Ramiso, design and development manager at Technology Enabler, discusses their activities, and the benefits of having a design services team for an EMS company with I-Connect007 Managing Editor Stephen Las Marias.

Better Together: How HDP User Group Showcases the Industry’s Best Side

HDPUG is a non-profit trade organization comprised of members from top companies in the electronics industry, from materials suppliers and manufacturers, to OEMs and end users. Key activities include collaborating on issues facing multiple industries and bringing people together on projects who might not have met otherwise. Barry Matties met HDPUG’s European representative and project facilitator Alun Morgan at the recent EIPC Summer Conference to learn more about the group and current projects.

Global Impact on European PCB Fabrication: EIPC Summer Conference 2017, Day 2

The second day saw the conference room full once more, the late networking session in the bar having resulted in no significant casualties, and I was pleased to accept the invitation to moderate the first session, on processes and materials for flexible PCBs.

Romania’s PCB Design Students Compete at TIE 2017

During the last week in April, the 26th Interconnection Techniques in Electronics (TIE) show was held at the Gheorghe Asachi Technical University in Iasi, Romaina, a wonderful hill town not unlike Rome. The event, a convention for the Romanian electronic packaging community, included a series of actions designed to draw smart young students to the electronics industry, which is clearly growing. Participants had only four hours to create this PCB design, which was generated by a team of professionals from Continental Automotive Romania Timisoara.

Global Impact on European PCB Fabrication: EIPC Summer Conference 2017, Day 1

Electronics industry professionals from 13 countries, mainly from Europe and Scandinavia, others from the USA, but some from as far away as India and Japan, gathered in Meriden, the centre of England, for the EIPC Summer Conference.

Must Work Well on a Team; CID a Bonus

Throughout my decades-long career in PCB design, I have been fortunate. I’ve only had to search for a job out of desperation once. I had no idea my IPC Certified Interconnect Designer credentials would come in handy when I hit the pavement. It also helped that I am known to "work well on a team." It turns out that being able to play well with others is a real plus in the PCB design community.

Whose Fault is it When the Board Fails?

In an upcoming issue of The PCB Design Magazine, we will discuss a question that you've undoubtedly faced in your job: Whose fault is it when the board fails? Of course, everyone likes to blame the PCB designer. But think about it. Is the board shop at fault, or perhaps the EMS provider? Is it the customer's fault, or does the designer bear some of the blame after all? Take this quick survey and let your voice be heard!

HDP User Group 2017 European Meeting Highlights Technology Progress

The conference facility at the offices of Oracle, in the royal burgh of Linlithgow in West Lothian, Scotland, was the venue for the 2017 European meeting of the High Density Packaging User Group. I was delighted and privileged to be invited once again to sit in on the open session, an intense programme of technical presentations and discussions, project reviews, status updates and new project proposals.

PCB Design in the Age of IoT

From the early days of printed circuit boards, the electronics industry has made huge strides in board materials, copper printing methods, miniaturization, rigid-flex, ELIC, EDA, and much more. Many of the devices we use in our homes, our vehicles, and in our workplaces would not be possible without this continuous evolution of PCB design and technology. And yet in 2017, we are poised to shift from evolution to revolution, driven by the idea of the Internet of Things.

SnapEDA: Recruiting Top Engineering Talent in an Amazon World

You don’t have to love EDA to work at SnapEDA, but it helps. This startup, founded by Natasha Baker, is on its way to creating the world’s largest parts library for PCB designers. Baker leads a small team of young, fiercely talented engineers—the kind of employees that are attractive to companies like Google and Facebook. I asked Natasha to explain her hiring process, and how she ensures that each employee is the right fit for SnapEDA.

Steve Robinson Discusses APCT’s Tenfold Expansion

Steve Robinson, CEO of APCT, a PCB fabricator in Silicon Valley, has led the company to impressive growth since he acquired it nearly 10 years ago. I ran into Steve at DesignCon 2017, and we sat down to discuss the company’s remarkable transformation and his focus on working with PCB designers and engineers to create advanced, high-speed PCBs.

Altium Focuses on the Designer First

A few months before Judy Warner joined Altium, while she was still with I-Connect007, she sat down with Lawrence Romine to discuss the company’s drive to satisfy the individual PCB designer, and not necessarily the OEMs who employ them. Romine also explains what sets designers and engineers apart from the average person, and why some Altium users have a different primary EDA tool, but use Altium when they need a design done fast.

San Diego IPC Designers Council Meeting Held at Del Mar Show

The Del Mar Electronics and Manufacturing Show is a long-time favorite among PCB professionals. What better place to hold a meeting of the San Diego Chapter of the IPC Designers Council? Each year, the San Diego Chapter of the Designers Council hosts their largest meeting of the year at the Del Mar show. This year, approximately 50 PCB designers and electronics professionals attended the lunch-and-learn meeting.

Bruce Mahler Discusses Ohmega’s Resistive Material Technology

Bruce Mahler, vice president of Ohmega Technologies, sat down for an interview with me at DesignCon 2017. He discussed the company’s latest embedded resistive materials, as well as some of the drivers and challenges in that segment of the materials industry.

Sensible Design: Casting a Spotlight on Resin Applications

Over the last few columns, I’ve given readers pointers on virtually every aspect of potting and encapsulation resins, ranging from their formulations and special properties to their applications, benefits and limitations. It’s probably high time, therefore, to take a step back from the do's and don’ts and focus instead on how these resins are bringing very real benefits to practical electronic and electrical engineering applications. A good starting point is to look at the special requirements of an industry that is enjoying explosive growth: LED lighting.

IMPACT Washington 2017 Just Around the Corner

IPC's Government Relations team has worked around-the-clock to ensure that IMPACT Washington D.C. 2017 is the best yet. During this two-and-a-half day event, executives from IPC-member companies will have the opportunity to speak with leaders in Congress and the Administration in support of our common priorities.

TTM Shines a Light on Optical Interconnect

Are embedded optics on PCBs set to make a breakthrough in the upcoming years? According to Dr. Craig Davidson, VP of Corporate Technology at TTM, it might be closer than you’d expect. In a recent interview with the I-Connect007 team, Craig outlines TTM’s current pursuit of high-volume manufacturing lines able to deliver embedded optical interconnect, what that would mean for the PCB industry, and why he thinks there will be manufacturing production capability by 2020.

'Flexdude' Tom Woznicki Celebrates Company’s 25th Anniversary

Twenty-five years ago, Tom “Flexdude” Woznicki got laid off. A lot of people did, back during the mini-recession that helped bring Bill Clinton into the White House. So, he launched his own flex circuit design bureau and never looked back. Since then, he’s designed flex circuitry for everything under the sun, including the Mars Rover; the flex circuits he designed are visible in many of the Rover photos. I ran into Tom at DesignCon 2017 and we discussed the benefits of flex circuits, the expansion of the flex market, and his company’s first quarter-century in operation.
Subscribe | Magazines | RealTime with | JobConnect007 | Education | Webinars
Copyright © I-Connect007 | IPC Publishing Group Inc. All rights reserved. Log in